How to Remove Chrome from a Priora Radiator Grille ~ SIS26.RU

Body-matched grille

For the work you will need a screwdriver and an awl. Auto mechanics distinguish 2 methods for dismantling the grille.

The bumper is removed.
The bumper cannot be removed.

At the first stage, the ground wires are disconnected from the battery. Then the engine mudguard is removed. To do this, you will need to unscrew the 3 bolts from below that attach the bumper to the protective covers. The next step involves removing:

screws securing the bumper to the front of the body;
2 screws for fixing the left and right headlight housings;
2 screws on the right and left side of the arches, they attach the bumper to the front fenders.

Removing the grille is completed by removing the bumper. If you remove the Priora SE grille using the second method, then you will need to press the locking washer located near the bumper. Then the washers securing the grille are removed. Otherwise, the hood is raised and secured with a stop. After this, the screws securing the combination lights to the front panel are removed. The lights themselves are removed, the electrical wiring is disconnected from them. Using a screwdriver, turn the locking washers 1/4 turn. The old grille is then tilted forward, pulled up and removed.

Replacing and tuning the grille on a Priora se are processes that require attention, since this unit provides maximum air flow to the radiator. The procedure will not take much time if you install a branded radiator grille. To secure it, you will need special parts. To do this, it is recommended to determine in advance the location on the bumper where this unit will be installed. In this case, a sealant is used.

Replacement steps

Body tone grille

You will need a screwdriver and an awl for the job. Auto mechanics distinguish between 2 ways to disassemble a grill.

The bumper has been removed.
The bumper is not removable.

At the first stage, the mass of wires is disconnected from the battery. The mud motor is then removed. To do this, unscrew the 3 bottom screws that secure the bumper to the protective covers. The next step involves removing:

The screws that secure the bumper to the front of the body;
2 screws securing the left and right headlight covers;
2 screws on the right and left sides of the arches, they secure the bumper to the front fenders.

Removing the grille ends with removing the bumper. If you remove the Priora se grille using the second method, you need to press on the lock washer located next to the bumper. Then the washers that secure the grille are removed. Otherwise, the hood rises and closes in focus. The screws that secure the combination lights to the front panel are then removed. The lights themselves have been removed and the wiring to them has been disconnected. Using a screwdriver, turn the lock washers 1/4 turn. Then the old grate

The radiator is tilted forward, pulled up and removed.

Replacing and adjusting the Priora se radiator grille. These are processes that require attention as this device ensures maximum air flow to the radiator. The procedure will not take much time if you install a branded radiator grille. You will need special parts to fix this. To do this, it is recommended to determine in advance the location on the bumper where this unit will be installed. In this case, a sealant is used.

Tips for choosing and installing a new radiator grille for Lada 2015

Before you begin replacing the radiator protective frame, you should study the recommendations and experiences of those who have encountered this issue:

1. When selecting a new radiator grille for Priora Lux, you need to pay attention not only to the external design, but also to the quality and practicality of this product. This will ensure a long service life and reliable protection of the radiator from external factors;
2. Grilles with saber-shaped horizontal stripes have the property of accurately directing the air flow to the heat exchanger, unlike conventional factory grilles Lada 2015;
3. Protective mesh in the bumper design allows you to reliably protect the car’s radiator from external factors that can damage parts of the engine cooling system.

In winter, experts recommend using special covers on the radiator grille, which allow you to save fuel when warming up the car in the cold season.

Replacing the radiator grille on a Prior

For some, the radiator grille is just an external appearance, but for others it is also the safety of the car’s cooling radiator. If the car does not have a radiator grille installed, then a pebble flying towards the car may simply fall into the cooling radiator, then this can cause deformation of the radiator itself. radiator and as a result you will have to change it to a new one, because if you don’t change it, then you will have constant problems with cooling the engine, and the leaking coolant will contaminate the engine and you will also need to constantly add coolant to the tank , therefore, it is recommended to replace a worn or deformed radiator immediately and not bother with replacing it, but still, now we are discussing not the radiator but its grille, not all people know how it can be changed on a car, although it is only attached to small washers, removing which you can simply remove the grille, and you will now learn how to do this from this article on replacement.

The main reasons for changing the grill

Another design option

Adjusting and removing the grille is necessary to give the car an original look. Car owners should know how to replace a part if it cracks. It should be noted that this design has:

Resistance to large temperature changes;
Personality;
Low price.

Priora tuning involves installing an “aggressive” radiator grille. This model will give the car a sporty look by increasing radiator cooling. Some Lada owners prefer to install factory models. You can use chrome strips and moldings. They stick easily to the ribs.

Of the necessary tools:

grille from Priora is easy to adjust with your own hands. To do this, you will need to cut the VAZ icon with a hacksaw. Then you need 2 moldings, which are pre-applied to the plane, marked and cut to size. This element is attached to the grille with tape. The forms must be pre-wrapped with adhesive tape. This will prevent damage to the main element.

READ How to Remove the Tail Light of a Passat B6

The next step is to dilute the epoxy glue in a container. They are covered with moldings and grilles. The strips are then applied, pressed and held in place for a while. After the glue has dried, the edges are trimmed. The file is used for this.

The value of tuning

Tuning is a modification of a car that allows you to improve its appearance and change its factory characteristics. With the help of tuning, engine efficiency and power are increased, suspensions and braking system performance are improved.

Tuning the grille allows you to improve the appearance of the car, as well as increase the protection of the radiator. Refinishing can hide damage and defects.

Main options

Before starting work, you need to determine the final type of grating. There are several types of modifications. The chosen type determines what materials and tools will be used in the work.

Most often, the radiator grille is replaced with a metal fine mesh. ABS or fiberglass construction is also used. Using silicone glue, various decorative elements (for example, brand labels, letters and even drawings) can be attached to the part.

When doing tuning yourself, you must avoid partially or completely blocking the air flow through the grille. Otherwise, due to a decrease in the efficiency of the cooling system, overheating of the lower part of the body is possible.

How to tune it yourself?

Independent modification of the radiator grille is carried out in several stages.

Removing the factory radiator element

To carry out work, the part must be removed. Usually the grille is fixed with bolts and self-tapping screws. But modern models are equipped with plastic latches. Dismantling is carried out carefully so as not to damage the fasteners and grooves intended for them. You can remove the grill in about 20 minutes.

Making LED lighting

LED lighting is placed around the perimeter of the removed part. To install it, you should think about the connection in advance. It cannot be attached to parts that heat up during movement. It is best to install diodes on the grille ribs. You can securely fix the tape using silicone or quick-drying glue.

Make part of the production

grille from Priora se is easy to make yourself. To do this you will need the following materials:

Where to remove the screws from the radiator grille

Firstly, the old block is dismantled. The puzzle cuts the middle of the piece. Holes are drilled at the mounting points for adjustment. Then you will need a thin and flexible material. plastic or cardboard. It goes around the inner contour of the future block. It is recommended to note how many centimeters the part will fit inside. Based on the obtained dimensions, cardboard or plastic is cut.

Lattice

The radiator is well cleaned with sandpaper and degreased. A solvent is used for this purpose. Apply to the area of contact with epoxy resin. Otherwise the connection will be weak. To get reliable contact and the desired thickness, you will need to repeat this process. As each layer dries, the product comes out of the cardboard or plastic. This will determine if the material fits snugly. The next step is to level the surface. Putty is used for this purpose.

When sanding, make sure there are no holes or scratches on the radiator grille. The main task. keep the product safe and secure. It is then coated with paint and primed. The setup is complete. The radiator grille is in place. To do this, you will need to bend it at several points.

Removing the front bumper upper grille

Required: pliers, long and short straight screwdrivers.

Loosen the 6 upper bumper mounting screws;
Bend the top of the bumper along with the grille;
Remove the mounting washers (on Priora SE, unscrew the screws) of the upper bumper grille by inserting a hand with a short screwdriver into the resulting hole;
Remove the upper bumper grille by pulling it towards you.

Removing the upper part of the Lada Priora radiator grille mounting from the Lada Priora radiator grille without removing the bumper

It is worth noting that owners of large hands cannot fold their arms or break the top of the bumper. Mounting diagram for the upper and lower bumper grilles:

Lada Priora bumper (radiator) grille mounting diagram

How to remove the radiator grille of a Lada Granta?

Wrenches for “8” and “10”;
Screwdriver;

1). Open the hood;

2). Unscrew 6 bolts from the top of the grille;

3). We bend the grille and, sticking our hand into the resulting gap, unscrew by touch the 4 bolts on top and 5 nuts on the bottom from the inside of the grille.

Setting up Lada Priori with moldings

The work is quite simple. no special skills required.

Remove the grille;
Cut out the VAZ icon located in the middle;
Note the 2 chrome moldings, lengthwise and cut to size with a hacksaw;
Using epoxy resin, we glue the moldings onto our base and wait for it to dry;
If necessary, indicate all inequalities in the file;
We install the resulting product on the car. and tuning is successfully completed.

In the photo you can see what grille (Lada Priora) will look like after performing this adjustment.

Content

How to remove the radiator grille on a Lada Priora

Selecting and installing a new grid

Modifying the grille on a Lada using moldings

Recommendations

Replacing such an element as the Priora radiator grille often arises in the minds of owners of a Lada car of this model. This car's grille doesn't have the most attractive appearance. To improve the appearance of the car, car owners often resort to tuning. Designers of automobile corporations never cease to amaze us with new forms and models of vehicles. Small details play an important role in the overall appearance. The radiator grille is no exception.

New radiator grille for Priora

There are always large holes on the bumper. They serve to keep the engine cool and the engine compartment to be freely blown and ventilated. A mesh is placed behind the radiator grille. It is designed to protect the insides of the car from various debris, insects, and small birds that can get under the hood while driving. The mesh performs a protective function. In tandem with the radiator grille, the mesh also plays a decorative role. This is why craftsmen love to experiment with this part of the body and make the car unique.

If you install a new grille on the Lada Priora, you can significantly change its appearance. Before you begin work on improving the design, you need to know how to remove the grille. Consultation with a specialist will not be superfluous. An experienced master will give advice, make recommendations and share the secrets of performing the work.

Replacing the Priora radiator grill is a simple process that you can do yourself. The process will depend on which grille you plan to replace the old one with. Before starting work, disconnect the wires from the battery and remove the engine splash guard.

There are two ways, with and without removing the bumper. To remove the grille on a Priora, you need to press on the washer that secures the bumper, and then remove the washers that hold the grille directly.

The Lada Priora se radiator grille is attached with nine screws, so there is no need to remove the bumper. Just open the hood and pull it out.

Replacing the radiator grille on a Priora

Grid Settings

You can use plastic or metal mesh. The installation process looks something like this:

Remove the grille;
Using a hacksaw, cut out all unnecessary vertical and horizontal elements, leaving only the outer contour;

Fold the mesh on the back of the Lada Priora grille

Seal the resulting holes with putty (some use fiberglass);
When the putty dries, grind until smooth. This is a rather labor-intensive process. you need to carefully monitor the shape and smoothness of the lines;
Primer;
Aerosol paint or regular brush;
Attach the mesh to the screw (the base must be heated so that it does not burst) or glue it if it is made of plastic;
Apply paint to the entire product;
Varnish;
Install back on the car. this work can be considered completed.

The level of protection for the engine compartment will depend on the size of the cells. You have to remember the right balance: with larger cells the cooling will be better, but the level of protection will be lower. With small cells. vice versa. When choosing a grid, try to stick to the “golden mean”.

Saber – article number, price

Sabers are special facing linings that are installed on the front and rear of the Priora. At the factory they are installed chrome plated, but with the help of simple tuning they can be changed.

radiator grille molding (saber) hood – 2170-08402104-00, price – about 700 rubles;
decorative trim (for the trunk of a sedan) – 2170-08212512-00, price – 900 rubles;
decorative trim (for trunks of hatchbacks and station wagons) – 2171-08212526-00, price – 1500 rubles.