The structure of the front seat, its removal and disassembly

More experienced Lada Vesta car owners prefer to do repairs themselves. For example, many can easily replace the fuel filter, change the routing of speaker wires, and soundproof the body. However, novice drivers may not know how to remove the rear seat. Lada Vesta is a car that will be quite easy to cope with this kind of task.

How to remove the rear seats on a Lada Vesta

The process of removing the rear seats on a car of this model will be simple and typical for most vehicles produced by the Russian automobile industry. A person can carry out this procedure independently, using a minimum of tools. During work, most often no difficulties arise if the driver follows a certain sequence of actions. But before you begin to consider the step-by-step instructions, you should understand in what situations you need to do this.

Why film?

Disassembling the rear seat is most often required in the following situations:

• 1. To replace the upholstery. Often, upholstery replacement is necessary if the fabric elements are damaged. This should include the appearance of stains from various drinks, holes formed as a result of wear, abrasions, and burnt material.
• 2. Body restoration work. Sometimes, after an accident, the rear of the car is damaged when the deformation occurs at the bottom of the passenger compartment. In case of side impacts in the rear or central area of ​​the body, it may also be necessary to replace the rear seat.
• 3. Replacement of seats. Some vehicle owners replace armchairs and sofas when tuning the body and interior.
• 4. Other reasons that require removing the rear seats.

Step-by-step instruction

To avoid any difficulties during the procedure, it is important to adhere to a certain algorithm of actions. Step by step guide:

• 1. First you need to find the latches that are located on the back side. They need to be pulled up. During manipulation, the horizontal part of the sofa should rise.
• 2. Next, you need to pull the entire seat by the backrest, and then remove the front latches from the grooves. During this action, the seat is completely removed and remains in the hands. If you planned to replace the fuel pump or filter, then it will not be enough to remove the lower part of the seat. To perform more complex installation work, the backrest is also removed.
• 3. To dismantle the backrest, you need to find four mounting bolts. For more convenient operation, first unscrew the seat belt latches. Then you can start unscrewing the bolts.

This completes the procedure for removing the seat on the Lada Vesta. The sofa is completely disassembled and dismantled. Even an inexperienced car owner can cope with such a task.

To reassemble the seat, all steps should be performed in reverse order. First, the vertical backrests are installed and secured with bolts. Next, the central seat belt is secured, and the sofa is installed on the brackets. Finally, gentle pressure is applied to the front area to record the result.

How to remove the seats of a Renault Logan is a question that arises for most owners of this car, who are faced with the task of transferring any oversized cargo. And this is natural, because its rear seats do not fold down . And in the trunk, with all its spaciousness, not everything can be transported .

Choice of seat upholstery

The best option in terms of price/quality ratio are ready-made kits for upholstering Chevrolet Cruze seats. Products are very popular. The price for them starts around 9,000 rubles. Premium models made of genuine leather can cost 20-25,000 rubles. In addition, seat upholstery can be purchased much cheaper in the markets, but this does not give any guarantee that they will look perfect. As a rule, such options can cost about 6,000 rubles, but will look like simple covers, moreover, installed crookedly.

After completing the work, the seats are mounted on the car in the reverse order of removal. In this case, you need to act carefully, trying not to damage the new seat upholstery.

If you are not confident in your “sewing” skills, then you can take the removed seats to a workshop, where they will be quickly and efficiently upholstered.

Removing the rear seats of Renault Logan 1

The procedure for removing the rear seats on a 1st generation Renault Logan is not that complicated. You don't even need a lot of tools. All you need is a wrench, a screwdriver and a helper since the back of the seat is heavy.

The procedure is as follows:

1. You need to remove the rear shelf, rugs, and anything that might interfere with work from the interior.
2. Then remove the seat cushion from the clamps by lifting it up.

Before placing cargo in the car and generally removing the rear seat, you should look at the instructions for your first generation Renault Logan. The fact is that the carrying capacity of vehicles differs, depending on the volume of the engine . In addition, you should be as careful as possible with small parts and fasteners.

If anything breaks, the seat will not be securely fastened.

How do car seats fold out?

To fold the seats in a car from France Renault Logan, you need to do a few simple manipulations:

• All front seats, including the driver's seat, can be reclined using the seatback tilt adjuster; you need to lower the backrest even to the level of the rear row seats, and then you get a spacious sleeping area that will appeal to those who like to travel.
• In the 2nd version of the Logan model, all rear seats can be easily and simply folded out using locking buttons, and you will not achieve a flat floor, but this design is much better compared to the 1st generation Logan.
• The 1st generation model initially did not have the ability to fold out the rear row of seats, and the only way owners had to increase space was to completely remove the backrests of the rear seats from the car.

Folding backrest of the rear sofa Logan 1

This is a small instruction for those who want to slightly improve their 1st generation Logan, make its rear sofa foldable.

You will need the following list of spare parts:

1. seat back lock 2108/09;
2. buttons for locking doors of classic VAZ (any model);
3. fasteners (bolts, nuts, washers). Tie clamps and a half-ring screw will not be superfluous;
4. a pair of hood hinges from the classic VAZ 2107;
5. pair of hood lock pins 2108/09.

The tool you need is this:

1. Bulgarian;
2. drill;
3. keys;
4. screwdrivers;
5. step drill.

The sequence of actions is as follows:

1. Remove the backrest of the second row of the 1st generation Logan. Unclench the rings that hold the trim in place to expose the bottom of the seat along with the frame.
2. Estimate the hinges; if necessary, you can modify them with a grinder. Drill holes for fasteners.
3. Cut off the so-called “tails” of the seat bottom fasteners, which are no longer needed. Secure the hinges and align the sheathing with their protruding parts. When returning the fabric to its place, it will be convenient to use plastic ties if you don’t want to mess with the factory rings.
4. Remove the plastic covers from the upper tongues of the back fasteners and drill holes for the lock pin. This part itself will also have to be slightly modified. The pin spring will have to be divided in half and the lower cup removed. The pin must be fixed in the hole on the back of the seat.
5. Return the backrest to Logan's interior.
6. Make marks in the metal for the holes where the lock pins will go, drill holes of approximately 2 cm, and also make holes for the fasteners of the locks, approximately 5-6 mm.
7. Next, drill through the metal of the rear shelf for the lock rods.
8. Then you need to make the lock rods. For this you will need VAZ “soldiers”, half-ring screws, and plastic clamps. It is important to correctly bend the half-ring screw, since the lock is located at an angle, and it is much more convenient to pull the toy soldiers up vertically.
9. By bending the plates with pins, you need to check that the opening and closing of the locks occurs without problems.
10. Next, remove the metal cross member and place the door seal from the VAZ 2108/09 onto the exposed metal so as not to scratch the transported goods.

In total, such parts for improving Renault Logan will cost approximately 2 thousand rubles.

Logan 1 front seat repair

Sooner or later, the driver's seat needs repairs. Therefore, below we will present instructions on how to return the front seats of Renault Logan to their previous appearance:

1. Remove the front seats and bite off all the staples that hold the upholstery in tension.

2. Bite off the top and bottom fasteners - they are hidden in the folds of the seat. It’s difficult to get in there with your bare hands; you can use medical clamps or something similar.

3. The first generation Logan upholstery is machine washable. If necessary, you can replace the foam rubber with a new one, using the old one as templates. But thick layers will be required.
   Read also:  VAZ 21214 will not start, the injector the starter turns, there is a spark
4. Next you need to assemble everything onto the ties. It will take a couple of packages. If it is necessary to replace the seat grilles, then their part numbers are: Renault 60-01-547-721 (lower), 60-01-547-723 (upper).
5. Assembly is carried out in the same way as disassembly. And if you change the driver's foam backrest with the passenger's, you can get fresher lateral support.

If done without interruption, the work is completed in about seven hours. But you can save money.

Video on how to remove the front seat from a VAZ 2114-13-15:

The front seat of the VAZ 2108 2109 21099 is removed if it is broken or during anti-corrosion treatment of the body inside the cabin. The rear seat, opposite, is removed very often, especially if the car is used to transport anything: you can put boards, a refrigerator, 6-7 bags of potatoes, etc. When you remove the back seat, the car becomes very roomy, as every owner of a V8 and Nine knows. Also, the rear seat has to be removed to deal with problems with the fuel level sensor or the fuel pump on the injector, since it is located directly under the seat. In order to dismantle the seats, the following tools are required: 1) A straight and Phillips screwdriver. 2) 13mm wrench 3) 8mm socket. Removing the front seats: 1) Using a 13mm wrench, unscrew the four nuts under the seat.

Removing the front seat of a VAZ 2109

Now its front part can be lifted up. 2) Unscrew the four bolts that secure the slide to the car body.

Raise the seat up

This is done using a 8-mm socket. If the bolts have not been unscrewed for a long time, they are unscrewed with force.

Front seat sliders

3) Remove the seat and take it out of the car.

VAZ 2109 seats removed

Removing the rear seat: 1) First, unscrew the two bolts securing the back of the rear seat to the body. Some people who frequently remove the rear seat do not bolt the backrest, but simply insert it into the guides.

Rear seat guides VAZ 2109

2) Bend the lever behind the backrest and, pressing along the edges, squeeze it out of the fastenings.

Backrest lever

Bend the seat

The rear seat back has been removed. 3) In order to remove the nine rear seat cushion, you need to unscrew two bolts with a Phillips screwdriver. 4) Then lift the pillow slightly and pull the lever underneath.

Lever under the rear seat

Then the seat will be removed.

The procedure for installing the seats is the reverse order for removing them and is not difficult at all. Produced using the same tool.

What to pay attention to:

— The studs to which the front seat is attached may become warped due to rotten metal underneath. Try not to deform them again, as they may fall off and will have to be welded. — The 8-point bolts that secure the front seat slides to the body must be unscrewed with a 8-point head. You simply cannot get to them with an open-end wrench, and they are tightened with good force.

Car : VAZ-2110. Asks : Sergey Mailyev. The essence of the question : I want to remove the front seat for reupholstery, how difficult is it?

I want to remove my seat for reupholstery. If it works, I'll drag the rest too. Tell me what difficulties I may encounter when removing the front seat on a VAZ-2110. And how difficult is it to put it back on later?

I want something like this!

Removing and installing the rear seat of Lada Granta

Tools:

• Ratchet wrench
• 10 mm head
• Open-end wrench 10 mm
• Medium flat screwdriver

1. Remove the rear seat cushion hinge plugs.

2. Lift the front part of the airbag up and remove the airbag hinges from the holders on the body.

3. Remove the rear seat cushion.

4. To remove the rear seat back, use a 10 mm wrench to unscrew the backrest mounting bolts from the trunk side: on the right (see first photo), in the center (see second photo) and on the left (see third photo).

5. Then unscrew the rear seat backrest mounting bolt located centrally in the passenger compartment.

6. Remove the rear seat back from the interior.

7. Install the rear seat onto the vehicle in the reverse order of removal.

Removing the front seat on a VAZ-2110

On a VAZ-2110, the front seats rarely have to be removed, but every owner of such a vehicle needs to know how to do it correctly. The whole procedure does not take much time and does not require special tools.

1. The key is "8".
2. The key is "13".

Process

1. Move the chair all the way forward.
2. Remove the torsion bars.

Using a 13mm socket, unscrew the 4 nuts securing the brackets and remove them.

Important! If your car has a heated seat system, you will also need to disconnect the wires.

After this, the chair can be removed from the cabin. Assembly is carried out in reverse order.

We take out the chair through the front door.

How to fold out the back seat in a Grant

Below watch a video about how to fold the rear seats of a Lada Granta and express your opinion about it in the reviews of the article.

Video quality: DVD

The video was uploaded to the admin from the user Avtandil: for immediate viewing on the portal.

To give the correct answer to the question How to fold the rear seats of a Lada Granta, you need to watch the video. After viewing, you will not need to seek help from specialists. Detailed instructions will help you solve your problems. Enjoy watching.

Humor on the topic: Boys and girls, if you experience awkwardness and embarrassment during dating, then it’s better to immediately move on to sex.

Any modification or tuning of a car begins with the disassembly stage. It is necessary to dismantle the seats in a number of cases, for example, to install additional sound insulation, install seat covers, etc. Below you will find instructions for removing the Lada Granta/Kalina 2 seats yourself.

Front seat

You will need : TORX E10 wrench (asterisk).

1. Move the seat as far back as possible and unscrew the 2 bolts securing the slide (in Fig. No. 2).
2. Move the seat forward as far as possible and unscrew the 2 rear bolts (No. 3 in Fig.).

If your car is equipped with heated seats, then you should disconnect the block with wires. Then remove the seat of the Lada Grant.

Types of toilet seat designs

Difficulties with the toilet lid are in second place among the breakdowns of this sanitary device.

A few years ago, the toilet seat had a simple design and was limited in the number of models. These days, the plumbing market offers a wide range of products. In addition, the covers can be equipped with additional functions. For example:

• built-in bidet;
• seat heating;
• micro-lift.

Several factors can lead to product failure:

• long-term operation;
• manufacturing defects;
• careless use.

As a result of any of the above reasons, cracks may form on the toilet lid or the fastenings may fail. In both cases, you will need to replace the old toilet seat with a new one. The products themselves have two varieties:

1. Articulated. The most common option. It is a structure made of a toilet seat, which is fixed to the base of the toilet using hinges. Hinges can be either plastic or metal. The first option is not subject to corrosion, but is inferior to metal hinges in strength and service life. Therefore, this design has to be changed more often. Chairs with metal hinges are installed on more expensive models, for example, with a micro-lift. Whereas the plastic option is inexpensive, so they are used to equip more affordable plumbing fixtures.
2. Micro-lift. This is a more modern mounting option. It is a semi-automatic design that raises and lowers the toilet seat. The installation method for a micro-elevator is no different from the conventional version. But there are several engineering nuances that should be taken into account when replacing the product. Thus, the fastening mechanism consists of a spring, a rod, a cylinder and a piston. They are the ones that move the lid. Failure of any element leads to the replacement of the toilet seat. After all, without the appropriate skills, it will not be possible to repair a micro-elevator.

Reference! The first mention of the toilet is dated 1 AD. e. It was invented in Ancient China. The covers for the plumbing fixtures were made of varnished wood.

Isis. Body, interior ⇒ Front passenger seat.

Moderators: cayman, ss67

Post by IMax » 25 Oct 2008, 16:28

For a long time now, almost since the purchase itself, something has been ringing unpleasantly in the seat. Recently, the ringing and rattling became unbearable and I decided to disassemble the seat.

But everything is in order. All landmarks along the way:

1. In order to remove the right part of the plastic seat cover you need to: — Unscrew the screw of the backrest adjustment handle. — Remove the handle. It just comes off backwards. — Unscrew the screw under the base of the handle. — Separate the casing from the central part by placing your hands in the backrest hinge and pulling to the right. The fasteners will come apart like a zipper. — Separate the casing fastenings along the seat at the top and bottom. — Move the casing forward. 2. In order to remove the left part you need to: — Remove the backrest tilt adjustment knob. It has a latch on the inside that needs to be picked up with a screwdriver. — Unscrew the screw under the handle. — Separate the casing as on the right. — Press forward. 3. In order to remove the covers covering the chair lift hinges, you need to pull them towards you. They will come unfastened. 4. In order to remove the front part of the chair bottom casing you need to: - pick up the plugs that are located at the back on top of the longitudinal guides. - Unscrew the screws under them. - remove the casing. 5. In order to remove the soft part of the seat, you need. — bend the two black flaps at the front bottom on the inside of the seat. Pull the edge of the seat upholstery down along the entire perimeter. — Open the white connector under the seat. — Raise the seat up. 6. I haven’t figured out how to completely separate the seat and remove the rear part of the casing.

Now about what was ringing: 1. The right backrest adjustment hinge was loose. The backlash would have to be determined by a small, weak spring, which would not ensure the motion of the hinge at rest. I shortened the spring and increased the tension of the cable that drives the mating part of the hinge on the left. The cable tension is adjusted on the left hinge. The adjustment depth did not provide the necessary tension, and I had to make a knot in the cable. 2. The mechanism for locking the longitudinal seat adjustment was shaking. Just hanging out. How it was even planned to fix it is not clear. I did not find any return springs or rubber bumpers. Therefore, I reduced the free play of the longitudinal adjustment knob, which is located at the rear, with a wire. 3. The lever for opening the seat lock, which locks the chair in a horizontal position, was dangling and ringing. The play on the lever axis reached 3 mm. I wound an elastic band around the axle and secured it with copper wire on top. It stopped ringing.

How to remove a toilet seat

Before you begin dismantling the cover, you should prepare the necessary tools. So, you will need:

• hacksaw;
• socket wrench;
• pliers.

The dismantling steps are as follows:

1. Unscrew the bolts. Whatever model of toilet seat is used, it is fixed to the base of the plumbing fixtures using two bolts. First you need to try to unscrew them by hand. If this does not work, use a socket wrench.
2. If the bolts turn, fix them with pliers.
3. If you can't remove the bolts with pliers, cut them off with a hacksaw. But this is a drastic method, so try first treating the bolts with lubricant and try unscrewing them with a wrench again.

Once the cover is removed, you can begin cleaning. As soon as the event is over, the toilet seat can be sent to its rightful place.

Reinstallation steps:

1. Installation of bolts. First, they should be secured in the structure of the toilet seat. After which they are installed in the corresponding holes on the base of the toilet and secured with nuts.
2. Adjustment. The seat position should be adjusted and the bolts should be tightened tightly. If you are installing a micro-lift system, you must first make sure that the system fits tightly to the base of the plumbing.

Now you know how to remove the cover to clean it. This is quite easy to do. The main thing is that all actions must be performed carefully so as not to damage the seat and the plumbing itself.

The problem of removing the front seat on their car usually arises among car enthusiasts in the following situations:

• Covers must be worn. Many drivers know that it is impossible to put covers on the seat so that they fit completely and follow the curves without removing the seat, since the cover is secured with a special hook under the seat.

Covers are usually changed when selling or buying a used vehicle to restore the interior. Also, new covers are purchased by those car enthusiasts who want to add new, fresh notes to their car. Additionally, a lot of people wash their covers to keep them clean.

• The seat needs to be repaired or reupholstered, and sometimes even replaced.

Owners of used, old cars, whose seats have virtually no lateral support, are usually concerned about replacing seats, which makes the trip not entirely comfortable. Often people do not attach importance to such trifles, but after driving a car with lateral support, everyone wants to install a similar seat for themselves.

The driver’s lifestyle also affects it. The average driver spends about three hours a day behind the wheel, which puts stress on the spine and negatively affects posture. The result is back problems.

So, let's consider a step-by-step mechanism of actions that will help you correctly remove the front seat:

1. The very first step is to remove the ground from the battery (negative wire). This is necessary in order not to disrupt the car’s electrical system, because most cars have wires in the seat - electrical wiring, heating and other useful functions.
2. Now you need to move the seat as far forward as possible.
3. A traditional seat is attached to a “sled”, which, in turn, is most often closed with plugs both in front and behind. These plugs must be removed and pulled out, or lifted up if they are latched.
4. The front seat is attached to the “sled” with bolts - this is necessary for transporting the seat back and forth. First you need to remove the caps from the rear mount, and then repeat this action with the front mount. Please remember to also disable the seat belt sensor.
5. The last step is to turn off the electrical equipment.

After the above manipulations, the chair is completely disconnected. Now you need to carefully remove it, so as not to damage the plastic interior, and remove it from the car.

Have you decided to remove the VAZ 2110 seat yourself? In this case, this is a step-by-step guide to removing the VAZ 2110 seat:

Move the seat all the way. Use a screwdriver to pull out the ends of the cables.

After we have moved the seat all the way, unscrew the 4 nuts that are shown in the picture.

We remove the brackets, after unscrewing the nuts they come off very easily.

Raise the front edge of the seats; this must be done after the brackets have been removed.

You also need to unscrew the 2 front bolts to secure the slide.

You need to unscrew the 3 rear bolts, but this must be done after you have removed the seat and removed it from the interior.

Remove the locking ring; it is located on the axis of the left slide.

The seat belt buckle bolt must be unscrewed.

We remove the tension spring from the slide.

We also unscrew the fastening bolt on the right slide.

You need to remove the inner sleeve.

And away with the outer sleeve!

How to choose chairs.

As it turned out, the seats are very different from each other and in order to install the seat smoothly, it must physically fit into the car. To do this, you need to measure all the distances, heights, widths and depths of the chair. When choosing a chair, it does not have to be the same size as yours, the main thing is that it just fits in the cabin.

However, there is one parameter that cannot be neglected: the width of the slide.

This is what motorists call the runners on which the saddle slides forward and backward. You need to know its exact dimensions from the axes of the bolts and the distance between the runners, since there are holes placed on them that coincide with the holes in the floor to which we attach the chair with mounting bolts. I can’t give you any advice on comfort, since each person has their own requirements for the chair and will have to measure it on themselves. The color characteristics of the chair should be combined with the interior of your salon and, of course, try to choose dark shades; light shades quickly get dirty and worn out.