How to check the ignition coil on a VAZ-2112 16 valves


Design and principle of operation of the ignition module

Some old-school motorists call the modules double-spark coils, which makes sense. After all, the coil is the predecessor of the ignition module in the technical evolutionary chain. The module is a paired design consisting of two pairs of windings (primary and secondary) and a switch that alternately switches low-voltage current from one coil to another. In some models of double-spark coils, the commutator is structurally located outside the block.

The operation of the module is controlled from an electronic unit that collects and analyzes information from various working components of the engine. The block, unlike the classic coil, has 4 sockets for connecting high voltage wires going to the spark plugs. The pulse occurs in pairs, first at terminals 1 and 4, then 2 and 3.

That is, each of the built-in coils is responsible for the operation of two cylinders. A spark occurs simultaneously, as a pair.

This is what one of the ignition module models looks like. The connector for connecting incoming wires is visible at the top.

At the input, the ignition module has a connector with four terminals. Usually most models have markings opposite them. Pulses from the Hall sensor alternately arrive at contacts A and B, serving as a signal to switch the commutator from one primary winding to another. C and D – ground and power supply (12 V), respectively.

Removing and replacing the ignition coil

In order to replace the module (ignition coil) on a VAZ 2112, you must perform the following steps:

  1. Before starting work, be sure to disconnect the battery by disconnecting the “-” terminal from it. (How to de-energize a battery.
  2. Then, approaching the ignition coil, disconnect one single high-voltage wire from its central part.

  3. Next, use a wrench to remove the two side nuts that hold the ends of the wires in place on the side of the coil.

  4. Next, when the nuts are unscrewed, remove both side wires from the coil.

  5. And to complete the operation, unscrew the two side nuts securing the ignition coil itself to the bracket.

  6. And then remove the coil from the car engine.

Possible causes of failure

The weak point of the ignition coils and modules is the secondary winding, which generates a high voltage pulse. A coil break or breakdown may occur in it. The following factors lead to this phenomenon:

  1. use of low-quality or unsuitable candles;
  2. operation with non-functioning high voltage wires;
  3. frequent attempts to check the spark.

The high-voltage pulse arising in the secondary winding must be realized (spent). If this does not happen (if the integrity of a high voltage wire is broken, for example), a high-energy electrical pulse seeks an outlet. He will find it, with a high degree of probability, in the thin secondary winding.

Often, a module malfunction occurs when the integrity of poor-quality factory soldering of wires going to the switch elements is violated. This happens from vibration. Also, the cause of non-working coils can be a banal contact failure in the incoming connector. Another factor leading to a malfunction of the ignition unit is often moisture that gets on the device during washing or driving in unusual conditions.

Symptoms of a problem

It is extremely rare for two built-in coils to fail at once, so it is more likely to be possible to start the engine with a faulty unit. However, even an inexperienced driver will immediately suspect something is wrong. The malfunction will appear as follows:

  1. unstable (floating) idle speed;
  2. the engine has difficulty picking up speed;
  3. characteristic sound of the engine (triple);
  4. jerking when accelerating (while moving).

Operating a car with such a breakdown is possible (you can drive to a garage or car service station), but it is not advisable unless absolutely necessary.

Similar signs of unstable engine operation are possible with a number of other ignition or fuel supply faults. To differentiate possible breakdowns, the performance of the ignition unit should be determined. It would be useful to check the contacts of the wires coming to the device, as well as their integrity.

Checking module power

Before testing the performance of the coils, you should make sure that a possible breakdown is not caused by a loss of power to the device. First, you need to try to simply restore contact by moving it several times or disconnecting/connecting the block of wires included in the connector. If such manipulation does not lead to improved engine performance, a tester (multimeter) is used to determine the quality of incoming pulses.

The block of wires is removed from the connector. On the block, each terminal (A, B, C, D) has a corresponding socket. Testing with the engine running is done as follows.

  • The first contact of the tester is in socket D, the second is to ground. The multimeter switch position is 20 volts. If there is power, the tester shows 12 volts.
  • The first contact is in socket C, the second is ground. Switch on ohmmeter (20 Ohm). Normally it shows less than 1 ohm, that is, the mass is normal.
  • The first contact is in socket B, the second is ground. 20 volt switch. The norm is not less than 0.3 volts. If this is so, it means that a normal pulse is coming from the Hall sensor to position B.
  • Contact A is checked similarly to the previous one.

If such a check shows the norm, you need to test the module. If not, look for the cause in the electrical circuit to the coil.

Methods for diagnosing device performance

The simplest method that will help determine the performance of the coil is to replace it with a similar working device. This is possible if there is somewhere to get it. Please note that the module must match the parameters of the device under test. If the engine with a working coil works as before the breakdown, the ignition module is definitely faulty.

The main testing method involves using a multimeter. It consists in determining the resistance of the secondary windings of the coils built into the ignition module. The method is simple and does not require additional skills.

The device does not need to be removed for testing. The check is done with the engine turned off.

This is how you check the resistance of the secondary winding with a multimeter

  • High-voltage wires are removed from the module sockets.
  • The tester switch is set to the 20 kOhm position.
  • The multimeter rods are placed in turn in the recesses of the corresponding contact pairs (1 and 4, 2 and 3).
  • With an intact secondary winding, the performance in both cases is the same. Normally, the resistance should be about 5.4 kOhm (in some models the indicators differ, which needs to be clarified). If the resistance is much greater, then there is a winding break. The resistance is much lower - a breakdown. The coil is faulty and cannot be repaired.

Video: How to check the secondary winding with a multimeter

When is there an option to repair?

If during testing both secondary windings show integrity and serviceability, the reason for the inoperability of the coils may be a break in the soldering of the switch wires. Such damage is detected when the rear cover of the module is removed. If you have a soldering iron and know how to use it, you can restore the integrity of damaged contacts, while at the same time strengthening the rest. This, unfortunately, is the only failure of the ignition module that can be repaired.

Testing the ignition module can be done using simple do-it-yourself instruments. Based on our advice, you will be able to fully check both the module itself and other elements of the mechanism that may be the cause of the breakdown. We wish you success in this matter!

If you find an error, please select a piece of text and press Ctrl+Enter.

Didn't find the information you are looking for? on our forum.

None Many pelvic guides with 16 valves will understand me.

These are the ones on the 124 engine, there are individual ignition coils, one for each cylinder, the impulse is controlled through the ECU with also four keys. In general, a system of this type has quite a lot of advantages, since in the event of any malfunction, the brain turns off the faulty key. BUT in RUSSIA this system has a very decent disadvantage that completely outweighs all the advantages. Namely, low-quality ignition coils, factory coils last quite a long time and with timely maintenance (replacing spark plugs, preventing the generator from overcharging) they can travel more than 100 thousand km. But as soon as the factory ignition coils fail, dancing with a tambourine begins!

Factory coils usually burn out one after another with a difference of 300-500-1000 km. If one burns out, then wait for the rest of the corpses))) The cost of a new coil varies from 700 rubles (domestic manufacturer) to 1300 (imported by BOSCH).

Not cheap at all for the pelvis. But the saddest quality of purchased coils is that, like many components, it leaves much to be desired, and I encountered this problem within a year, I changed 5 pieces and they burned out before traveling 15,000 km.

I got tired of this and decided to switch to an ignition module like on a viburnum. two-winding coil with high-voltage wires. To do this, I needed the coil itself, high-voltage wires for 16 valves, a coil connection chip and brain firmware, which I stupidly didn’t know about and didn’t read enough about.

I’ll tell you how I made the transition in the next post.

In the meantime, the culmination is that having assembled the entire system and without flashing my brains, I began to start the engine, which later turned out to be unsuccessful. The first attempt pumped quite a bit of fuel into the exhaust, the second attempt ignited it. And there was a decent boom (in Russian, it was so bad that my ears were blocked for about three minutes, the hair on the mechanic’s balls turned gray “from his words,” I didn’t check it myself, the men on the street sat down on the ground). And it became somehow clear that such an explosion could not happen without consequences. As a result

Bombed fart thank you all! especially to the two guys who read the previous entry and reacted somehow. The rest of the 700+ robots who were squeezing are nice to you too! You encourage me to paint the BZ)))

In modern cars, individual ignition coils (ICO) are used to supply a spark to the cylinder. Older cars use ignition modules, meaning one module is entirely responsible for firing all cylinders. An individual ignition coil is responsible only for the operation of one cylinder in which it is installed. IKZ began to be installed on VAZ cars, starting with the Lada Priora car on the 126th engine. An ignition module is still installed on 8-valve VAZ engines. The car's on-board network uses low-voltage voltage, which is not capable of itself forming a powerful spark necessary for engine operation. Therefore, ignition coils are used to supply high voltage voltage.

Video on repairing KZ VAZ

At different times, different engines were installed on the VAZ-2110 car, both carburetor and injection. However, regardless of the type of power system and the number of valves (8 or 16), all engines are assembled on the unit base of the old engine 21083 and 21093. The most progressive of these engines is the 16-valve 1.6-liter VAZ 21124 engine with a power of 89 horsepower. Today we will touch on the ignition module for 8-valve engines 2111 and 21114 (1.6 l), check its performance and find a suitable replacement for the failed module.

IKZ device

The Priora coil consists of a primary and secondary winding, between which a core is placed. To contact the spark plug, a spring is used, which is placed in a rubber tip. The IKZ also has a metal screen that protects the coil from high temperatures, because IKZ is installed in the well of the cylinder head, then the temperature conditions there are simply enormous. The primary winding is wound from thin copper wire with a number of turns of 10,000-15,000.

The secondary winding of the coil consists of 100-150 turns of thick copper wire. The connection between the coils is electromagnetic.

What is an ignition coil?

The coil is a pulse step-up transformer. It is she who ensures the conversion of low voltage, which is supplied to it from the battery or generator, into high voltage pulses.

Thanks to these impulses, a spark jumps between the electrodes of the spark plug, which ignites the working mixture in the cylinders.

Like any transformer, the coil consists of two windings (primary and secondary), a magnetic circuit and a housing.

The module is structurally somewhat more complex and includes two coils and a switch, but its operating principle is identical to the coil.

Signs of coil failure:

  • One of the cylinders does not work;
  • The car does not develop power;
  • Jerking when pressing the gas pedal sharply;
  • The engine shakes at idle;
  • Increased vibration at idle;
  • Floating speed;

It should also be noted that if the ignition coil is faulty, misfires will appear in the cylinders, as a result of which the ECU will turn off the operation of the faulty cylinder and signal this by turning on the “Cheek Engine” lamp. When “Cheek Engine” appears on the car, it is necessary to diagnose the system. If there are misfires, the ECU will display errors 0301, 0302, 0303, 0304. Where the last digits of the codes are the cylinder number. It is not recommended to operate a car with a faulty ignition coil; this can lead to failure of the catalyst.

Price of the ignition module VAZ 2114

Despite the fact that many owners of the “fourteenth” try to repair this module, experts consider such repairs to be ineffective. Therefore, if a malfunction occurs, it is recommended to replace the part. Its cost is 1000-1500 rubles , depending on the manufacturer and region of the country. Driving with a faulty ignition coil is not prohibited, but such driving will not be comfortable. The engine may not start at any time after stopping on the road. Therefore, it is advisable to stop using the car and change this element within a reasonable time. This can usually be done by hand.

Checking the ignition coil

There are two reliable ways to check IKZ: visual inspection and checking with a multimeter.

It should be noted that the IKZ check is similar for all Lada cars with a 16-valve engine, i.e. the check for cars such as LADA Vesta and X-ray will be the same.

In order to check the ignition coil, it must be removed from the car. Removing IKZ:

  • Disconnect the negative terminal from the battery.
  • Remove the decorative plastic trim.
  • We unscrew the coil we need with a “10” or Torx E8 head.
  • Remove the coil plug and remove it.

How to check the ignition coil on a VAZ-2112 16 valves with your own hands

The ignition coil, which is located in the car, essentially converts the low voltage from the battery and generator into high voltage, to supply it individually to each spark plug. Roughly speaking, this is a miniature electrical transformer, the moment of failure of which is almost impossible to predict and repairs and diagnostics have to be carried out on the failed device. Below in our article we will tell you in detail how to check the ignition coil for a VAZ-2112 with your own hands.

The video describes in great detail the algorithm for checking the ignition coil on a VAZ-2112:

Visual inspection

After the coil is removed, it must be carefully inspected. The rubber tip should not have tears or cracks. The plastic part must not be melted or cracked. The contact spring must be in the correct shape without oxidation or rust.

Crack in the coil Cracks in the coils or tears in the rubber cap will direct the spark to the engine body, therefore, no current will be supplied to the spark plug, which will lead to misfires.

Cracks in the elastic band of the coil If such visual faults are detected, the coil must be replaced.

Checking with a multimeter

Testing with a multimeter is divided into two stages. Checking the resistance of the IKZ itself and checking the control voltage of the IKZ (checking the voltage on the IKZ power supply block).

Let's start by checking the voltage at the IKZ power supply.

To do this, set the switch on the multimiter to constant voltage.

Turn on the car ignition

On the block in connector number 3 we take a measurement (we connect one multimeter probe to the motor body and the other to pin number 3) the voltage should be at least 12 volts. If the voltage is less, this means that the battery is discharged or the ECU controller is faulty.

Checking the IKZ resistance

In order to check the resistance of the IKZ, you need to use a multimeter. It should be noted that resistance measurements must be carried out on a cold engine, because The resistance of the coil windings strongly depends on its temperature. To check the resistance, it is necessary to check two windings, the secondary and the primary.

Checking the primary winding of the IKZ When checking the primary winding of the IKZ, it is necessary to set the resistance readings on the multimeter, namely 200 Ohms. Since the resistance readings on the primary winding are not large, and the error of the device is possible, you first need to find out the error of the multimeter. In order to find out the error, you need to close the probes together, the value that will be reflected on the multimeter screen will be the error.

In this case, the error of the device is 0.7 Ohm. Next, we connect the multimeter probes to contacts 1 and 3 (the outermost contacts of the IKZ) and obtain resistance readings. From these readings we subtract the multimeter error and get the true value of the resistance of the primary winding.

Ideally, the resistance of the primary winding should be about 1 Ohm, or better yet 0. In this example, the reading is 1.1 Ohm without taking into account the error; from 1.1 Ohm we subtract 0.7 Ohm to get 0.4 Ohm. Verdict: the primary winding of this IKZ is in working condition.

Checking the secondary winding of the IKZ In order to check the secondary winding of the IKZ, set the multimeter to 2000 kOhm.

We connect the red multimeter probe to the spring, and the black one to the middle contact on the IKZ (pin 2). We look at the readings of the device; on a working coil, the resistance of the secondary winding should be in the range of 300-400 kOhm.

As we see, the readings of the secondary winding are also within the normal range. It follows that this IKZ is working.

If the readings are too high, you can try removing the rubber cap and spring from the coil and cleaning the contact patch, then measure the resistance directly again without the spring. If the resistance reading still does not decrease, you should think about replacing the ICP.

The easiest method to detect a faulty ignition coil, without any devices or instruments. This is a reversal of the IKZ.

Examination

If you notice signs of a problem with the ignition coil, or have to deal with a situation where the engine “died,” be sure to check the condition of this element.

As you test, you will be able to determine what caused the coil to fail and how the problems can be corrected.

How to check the device? The instructions are not complicated, even a beginner can handle it.

First, let's check the condition of the unit, and then check for correctness of the resistance of the coil itself.

  1. If the engine cannot be started, make sure that the coil itself is producing a spark at all. To do this, the central wire is removed from the distributor and a spare spark plug is connected to it.
  2. Now take the spark plug with pliers and place the metal casing on the breaker or motor.
  3. If a spark does not appear when the engine starter is turned, there is a malfunction in the ignition system.
  4. So check the power to the coil, or rather its presence. For this you will need a multimeter. One terminal is connected to contact B on the coil, and the second goes to ground. Turn on the ignition. If there is no voltage, the culprit is the ignition switch.
  5. You can start the engine in emergency mode. To do this, the plus from the battery is thrown onto contact B of the coil.

If there is voltage but there is no spark, check whether the primary winding is intact. To do this, the side low-voltage wires are disconnected from the coil and resistance measurements are taken with a multimeter. Then the secondary winding is checked.

We will tell you about this procedure in more detail.

Multimeter for testing

Checking coil resistance

  1. Unplug your car. To do this, simply disconnect the negative terminal from the battery.
  2. Disconnect all wires and leads going to and from the coil.
  3. Be sure to arm yourself with the necessary tools and a tester. A universal multimeter or ohmmeter will work fine.
  4. Take measurements on the primary winding. To do this, the tester probes must be connected to the low-voltage terminals located at the edges of the coil. Before doing this, do not forget to clean the terminals from accumulated dirt and traces of oxidation. Surely they formed during the operation of the car.
  5. Record the data.
  6. Now the resistance of the secondary winding is checked. To do this, you need to transfer one ohmmeter probe to terminal B of the coil, and the second to the high voltage.
  7. Note your results.
  8. The last stage of the test involves measuring the insulation resistance to ground. To do this, you need to connect one terminal of your tester to ground (this is the ignition coil housing), and connect the second one in turn to all three terminals - a pair of low-voltage terminals and one high-voltage one located in the middle of the device. If the coil is working properly, then in all three measurement cases you will get a resistance of at least 50 ohms.
  9. Check the table against the previously recorded data.

[media= https://www.youtube.com/watch?v=2F4BDExybgs]

Coil typeWindingResistance indicators
3122.3705Primary winding0.43 ohms +/- 0.04 ohms
8352.120.42 ohm +/- 0.05 ohm
3122.3705Secondary winding4.08 ohms +/- 0.40 ohms
8352.125.00 ohms +/- 1.00 ohms

Repair

In fact, the only way to repair a faulty ignition coil on a carburetor or injection VAZ 2109 is to replace the device.

Here you just need to choose which element will replace your old coil.

  • MZATE-2. This is a standard coil, which all VAZ 2109s were equipped with from the factory. It costs about 600 rubles and serves well;
  • An excellent alternative option, characterized by reliability, durability and operational efficiency. But it costs about 1800-2000 rubles;
  • Valeo. Something between the factory and Bosch version, which has good characteristics and positive reviews. Today such a reel costs an average of 1,500 rubles.

The coil is the most important element of the ignition system; if it fails, you can forget about traveling about your business.

Have you ever had to check or repair an ignition coil?

  • Yes, I have carried out similar operations several times already.
  • No, the reel has never failed yet.
  • I’m going to do this kind of work myself for the first time, and I’m collecting the necessary information.

View Results

Loading …

Rating
( 1 rating, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]