How to properly remove the cigarette lighter on a Lada Granta. cigarette lighter grant

Causes of cigarette lighter malfunctions

So, everything is clear with the forms

But how to choose a device whose use will definitely not burn anything? It is very important to pay attention to whether the maximum electrical load is indicated on the device and what its value is. It should not exceed the standard 15 amperes. Another noteworthy feature is the current strength of the USB connectors.

It ranges from 500 milliamps to 2 amperes. It’s better in this case to take the maximum

Another noteworthy feature is the current strength of the USB connectors. It ranges from 500 milliamps to 2 amperes. It is better in this case to take the maximum.

Read more: Skoda Rapid low beam bulbs

If the device seems too fragile and unreliable in appearance, it is better to refrain from purchasing it. The most meticulously worth inspecting is the connectors of the splitter themselves, those round ones. There should be no circuit board protruding from the bottom of the splitter sockets. The contact sleeve of the splitter should not be too thin. If it appears to be no thicker than foil, the device may be dangerous to operate.

Even when using a high-quality extension cord, remember that the Kalina cigarette lighter is a fire hazard; under no circumstances load the splitter to its full capacity. Don't count on the fuse, because you already understand how quickly it gives out. You also need to be careful with the splitter. On one of the Kalina station wagons, the fuse mentioned above failed when only an empty splitter was connected. This is precisely because of those ill-fated contacts. But after replacing the fuse everything worked again.

Under no circumstances should a more powerful fuse be inserted. Only standard at 15 amps. Otherwise, the wiring will be completely destroyed under the increased load.

It is worth paying attention to the plugs. The ones that really fit will never cause a short circuit

The cigarette lighter may also stop working because dust and oxidation have accumulated in the fuse box. Many car enthusiasts say that if nothing burns out, then it’s only a matter of time. There are 2 simple solutions offered.

1. Deliberately break the cigarette lighter itself (that is, not the socket), connecting devices to a splitter.
2. Bend the contacts in the socket a little further.

Replacing suspicious plugs with more suitable ones also helps. Take a closer look at the devices that you want to power from the cigarette lighter, otherwise you won’t have enough time to change fuses.

Replacing the cigarette lighter with a USB socket

Due to the design features of the liftback, some difficulties arise with the cigarette lighter. The short body does not provide reliable fixation, which is why connected devices may turn off. Therefore, many owners install a 12-volt socket instead of a car cigarette lighter.

For this procedure, standard AvtoVAZ sockets for Gazelle, Vesta or XRay are suitable. Part number 118.3725 SOATE. The price of the device is 150 – 200 rubles.

1. We de-energize the car by removing the negative terminal from the battery or pulling out the corresponding fuse.
2. We take out the metal cartridge.
3. We bend the fixing antennae.
4. We dismantle the internal part of the car cigarette lighter.
5. Disconnect the wire block.
6. We connect the plug to the socket socket.
7. We mount it in the cigarette lighter hole.

The disadvantage of this procedure is that the device will stop working as intended. The socket will not be illuminated due to the removal of the filter. However, all connected devices are securely fixed in the socket. You can learn more about the installation procedure from the video.

Author of the material: Dumchenkov Mikhail

PROMOTION: SALE OF NEW CAR 2021 PRODUCTION

from 606,900 rub.

from 489,000 rub.

• Audi
• Brilliance
• Faw
• Ford
• Chevrolet
• Citroen
• Geely
• Haval
• Changan
• Chery
• Datsun
• Great Wall
• Hyundai
• Kia
• Lada
• Volkswagen
• Renault
• Nissan
• Toyota
• Honda
• Mitsubishi
• Opel
• Lifan
• Mazda
• Skoda
• Rest

• Acura
• Alfa Romeo
• Audi
• Bentley
• BMW
• Cadillac
• Chery
• Chevrolet
• Citroen
• Daewoo
• Dodge
• Fiat
• Ford
• GAZ
• Geely
• Hawtai
• Honda
• Hyundai
• Infiniti
• Jaguar
• Jeep
• KIA
• Land Rover
• Lexus
• Lifan
• Lincoln
• Mazda
• Mercedes-Benz
• Mini
• Mitsubishi
• Nissan
• Opel
• Peugeot
• Porsche
• Renault
• Skoda
• SsangYong
• Subaru
• Suzuki
• Toyota
• UAZ
• VAZ
• Volkswagen
• Volvo

• New cars 2019
• New cars 2018
• Test drives
• Jeeps

Repair and service

• Engine
• Chassis
• Electrical equipment

• Signaling
• Cigarette lighter
• Car Reviews
• Photo and video galleries
• News
• Tires

2020 Daciaclubmd.ru. If you do not agree with any provision of this Disclaimer, do not use this Site. Please read Disclaimer and Privacy Policy before use.

Removing the cigarette lighter, replacing the backlight lamp

We remove the cigarette lighter to replace it or to replace the cigarette lighter lamp.
Remove the central trim of the instrument panel (see “Removing the instrument panel”). We take out the cigarette lighter socket. Remove the guide of the cigarette lighter lamp socket.

...remove the cigarette lighter from the instrument panel.

By pressing the latch, disconnect the wiring block from the cigarette lighter.

Remove the cigarette lighter light guide from the instrument panel.

We remove the socket with the lamp from the light guide... ...and remove the lamp from the socket. We install a new W1.2W cigarette lighter lamp and the cigarette lighter in the reverse order.

The Lada Granta car is often equipped with a cigarette lighter instead of a regular socket, but many owners suffer from this option rather than enjoy it. The cigarette lighter connector in a modern car not only performs its direct role, but also serves as a power source for additional equipment located in the car: a recorder, a radar detector, a compressor for inflating tires and much more. And the Lada with cigarette lighters has a peculiarity: these devices have a body that is too short, as a result of which the plugs of the devices are held there extremely poorly and are not stable, which causes a disruption in their power supply, and also leads to a short circuit and the burning of the fuse. The latter is especially unpleasant, since the cigarette lighter fuse is also connected to the instrument panel, which stops functioning after the fuse fails.

To correct this ailment, you will need to purchase a standard VAZ socket, which in 2021 began to be installed on some versions of Grants, as well as on Vesta and X-Ray. Socket code: 118.3725 SOATE, average cost about 150 rubles.

Before starting installation, be sure to disconnect the negative terminal from the car battery to prevent the possibility of a short circuit, and also prepare a thin slotted screwdriver or awl.

The first step in replacing the cigarette lighter with a socket is to bend the top and bottom tabs that secure the metal part in the plastic socket. The places of the petals are marked in the photo.

Disconnect the power plug and remove the metal part of the cigarette lighter.

Then, in the same way, press the two plastic clips from above and below in the plastic part of the cigarette lighter socket and, shaking it from side to side, pull it out of its seat.

Plug the power plug into the wall outlet.

Thanks for subscribing!

Snap the socket into its seat until it clicks into place.

After the replacement, it will become impossible to use the cigarette lighter, since the heating element is slightly larger than the diameter of the socket. However, all additional consumers that you will now connect to the power connector will be fixed there much more securely and will not fall out when driving on uneven roads.

Replacing the cigarette lighter on Kalina 1st or 2nd generation

The repair process is practically the same for these Lada models. It is also relevant for the Grant or Priora family. To replace the cigarette lighter with your own hands on Kalina 1st or 2nd generation, just follow the following procedure.

1. Open the hood, find the battery and disconnect the negative terminal from it. It is recommended to remove it, because the mass is powered through the car body. If you turn off the plus, it will touch the body.
2. We unscrew the three mounting bolts around the parking brake handle, which is located on top of the central tunnel. We dismantle the hand brake limit switch.
3. We unscrew the rear fastening screw and additional screws on the sides.
4. Remove the cover from the gear lever, and then lift the tunnel cover. Now you can remove the Kalina cigarette lighter itself.
5. We disconnect the power plug coming to the electrical wiring circuit.
6. We press the special latches that hold the cigarette lighter. After it pops out, it can be replaced.
7. We install a new part on the Lada Kalina. After replacement, we carry out the assembly process. We perform all steps in reverse order.

Removal and replacement instructions

All car mechanics, without exception, recommend disconnecting the “-” terminal of the battery when working with the vehicle’s electrical equipment.

Preparation

Work on replacing electrical fuses or relays can be carried out anywhere. The main thing is that the place should be well lit. Before starting work, be sure to turn off the car.

Video about replacing the fuel pump fuse on a Lada Granta - to help you.

The work of replacing fuses in the cabin and engine compartment is almost identical. With minor differences.

Cover removal diagram

1. Let's start with the first one. To gain access to the fuses and relays located to the left of the driver's feet, you need to remove the cover.
2. This must be done according to a certain scheme. First you need to pull the cover by the lower left corner, it is designated as number 1 in the diagram. Next, release the left locking point. Then the middle one at number 2. Next are points 3 and 6. Now all that remains is to free the top points 4 and 5. The entire cover has been removed.
3. Visually inspect the block. There should be no burning or melting in it. There should also be no burning smell.
4. In the decoding we find the consumer we need and according to the diagram we find its location.
5. Using tweezers located in the block, remove the problematic element. We inspect it visually or check it using a device.
6. If it is burnt out, then we put a new one in its place.
7. The cover of the interior unit is installed in the following order: first of all, you need to snap the right part, then the bottom, and finally the top. It is necessary to ensure that the fastening parts of the cover and the latches match exactly.

1. If the element we need is located in the engine compartment, then we proceed somewhat differently, namely, we open the hood itself.
2. Find where the block is located.
3. Slide the cover up and remove. We determine the burnt out element, just like in the cabin unit.
4. We put the cover in place.
5. Connect the “-” terminal of the battery.
6. Turn the ignition key.
7. If the consumer earns money, then everything is in order.

If the fuse blows again, the problem may be more serious and you will need to call a professional to help.

When is replacement not needed?

In some situations, the cigarette lighter may not please the owner due to its lack of functionality. For now, this is not a reason to be inclined to replace it. First, it is advisable to check the serviceability of the fuse. It would also be a good idea to make sure there is stable contact with the ignition switch. The indicated “bottlenecks” should be carefully checked, and then a verdict about a malfunction of the cigarette lighter socket should be made. In most cases, the problem can be solved by correcting the specified defects. And then you won’t have to figure out how to remove the cigarette lighter.

Common cigarette lighter malfunctions

Among the most common cigarette lighter malfunctions you can see the following breakdowns and defects:

1. Blown fuse element. Let us remind you that the mounting block with inserts is located under the panel in the cabin. We are interested in the component labeled “F20”.
2. Broken filament of the power element.
3. Progressive corrosion on the socket contacts, as a result of which they do not “show” sufficient electrical conductivity.

Photo of the correct replacement

After carrying out the work, it is advisable to check the proper operation of the device.

1. The car cigarette lighter should fit tightly in the socket, and there should be no oxides or rust on the contacts.
2. You should measure the voltage on the battery, and then check again by turning on the ignition. If the drawdown is more than 0.5 volts, then there is a short circuit somewhere.
3. All soldered wires must be insulated and shrink-wrapped.

We act in the salon

1. The fuse box is located on the left side of the instrument panel. Remove the cover with the outdoor lighting mode switch integrated into it. If the work is carried out on the LADA Granta “Lux” and “Norma” modifications, then do not forget about the need to disable the button used to unlock the trunk lock.
2. Armed with the diagram, we determine whether the cigarette lighter fuse or the fuel pump fuse has become unusable, and so on. We look at the integrity of the thread and draw the appropriate conclusion. If the element is unfit, then we replace it with a new analogue by fixing it in the mounting socket. We repeat this action with the entire list of blown fuses.
3. We connect the “minus” back to the battery and check the functioning of the electrical unit in which the fuse was replaced.

The process of replacing the specified elements, which contain the fuse block, of the engine compartment of the Lada Granta is implemented in a similar way. The cover on the safety module is removed using a simple action - just pull it up and quietly replace the marked elements.

The device has become popular in recent years. Now even non-smoking car owners use the cigarette lighter. Indeed, in addition to its nominal purpose, the device performs a lot of functions. For example, various devices are connected to the cigarette lighter socket:

• power bank for mobile phones or tablets;
• charging for laptop and electronics;
• DVR;
• navigation system;
• electric pump that inflates the wheels.

When used correctly, the device works for a long time, but due to certain features it may fail. Read on to find out why the breakdown occurs, how to recognize the cause of the malfunction, replace the cigarette lighter or repair it on the Lada Granta model.

Fuse problem

A blown protective component (fuse) is the main reason why a car cigarette lighter stops working. The electrical network must have a current of 15 A. In the event of a short circuit or the connection of powerful electrical appliances, the fuses will blow. To eliminate the malfunction, it is necessary to change the protective element and remove the excess load, otherwise it will burn out again.

Where is

The 2021 Granta Liftback has fuses located near the driver’s left foot.

To change the protective element, first remove the plastic cover of the unit, which is held in place by steel clips.

On the inner surface of the protective cover there is a diagram, the number of all fuses with information about what each of them is responsible for.

Which one can I put in place?

The new fuse is selected with a rating of 15 A. If you install a product with high resistance, problems will arise. For example, if a current flows through an electrical circuit exceeding the permissible value, the wires will melt. And this contributes to cable fires, short circuits, and, accordingly, burnout of protective components.

Causes of cigarette lighter socket failure

The experience of the owners allowed us to narrow the range of “suspected” factors, the impact of which could harm the cigarette lighter socket.

1. A short circuit that may suddenly occur in the on-board network of the Lada Kalina. This negative phenomenon occurs due to various circumstances, usually appearing after unprofessional intervention in the electrical part. For example, after:

• improper installation and connection of the security system;
• the battery becomes unusable;
• penetration of moisture to open contacts;
• incorrect installation of non-standard electrical appliances, multimedia, etc.

2. Damage to the heating element due to overheating. The risk of spiral breakage cannot be ruled out.

3. Instability of the electrical contact in the outlet itself, mainly after oxidation.

4. Connection of additional current collectors. This action often causes an increased load on the fuse link, as a result of which its working element burns out.

Cigarette lighter selection

Not many motorists and Lada Granta owners know that in addition to the standard VAZ cigarette lighter, there are several more analogues of this part.

Cigarette lighter assembly

Let's look at the catalog numbers and names of the spare parts:

The original article number for the cigarette lighter is divided into 3 parts: 1. Movable part of the cigarette lighter (21230-3725200-00); 2. Cigarette lighter socket (21230-3725100-00); 3. Cigarette lighter illumination ring (21230-3725400-00). As you can see from the catalog number, the Lada Granta has a part from the Niva Taiga installed.

Both parts fit perfectly into the seat and do not require modifications or modifications to the fastening.

Reasons for cigarette lighter failure

There are several reasons for the failure of the Lada Grant cigarette lighter:

• Short circuit caused by a failure of the on-board network.

Melted cigarette lighter (remember that in the first versions of the Lada Grant you cannot insert anything into the cigarette lighter except the cigarette lighter itself)

Stories from our readers

“Fucking basin. "

Hi all! My name is Mikhail, now I’ll tell you a story about how I managed to exchange my two-wheeler for a 2010 Camry. It all started with the fact that I began to be wildly irritated by the breakdowns of the two-wheeler, it seemed like nothing serious was broken, but damn it, there were so many little things that really started to irritate me. This is where the idea arose that it was time to change the car to a foreign car. The choice fell on the melting Camry of the tenth years.

Yes, I had matured morally, but financially I just couldn’t handle it. I’ll say right away that I am against loans and taking a car, especially not a new one, on credit is unreasonable. My salary is 24k a month, so collecting 600-700 thousand is almost impossible for me. I started looking for different ways to make money on the Internet. You can’t imagine how many scams there are, what I haven’t tried: sports betting, network marketing, and even the volcano casino, where I successfully lost about 10 thousand ((The only direction in which it seemed to me that I could make money was currency trading on the stock exchange, they call it Forex. But when I started delving into it, I realized that it was very difficult for me. I continued to dig further and came across binary options. The essence is the same as in Forex, but it’s much easier to understand. I started reading forums, studying trading strategies. I tried it on a demo account, then opened a real account. To be honest, I didn’t manage to start earning money right away, until I understood all the mechanics of options, I lost about 3,000 rubles, but as it turned out, it was a precious experience. Now I earn 5-7 thousand rubles a day. I managed to get the car buy after half a year, but in my opinion this is a good result, and it’s not about the car, my life has changed, I naturally quit my job, I have more free time for myself and my family. You’ll laugh, but I work directly on the phone)) If If you want to change your life like me, then here’s what I advise you to do right now: 1. Register on the site 2. Practice on a Demo account (it’s free). 3. As soon as you get something on the Demo account, top up your REAL ACCOUNT and go to REAL MONEY! I also advise you to download the application to your phone, it’s much more convenient to work from your phone. Download here.

Second cigarette lighter in the car

The easiest way, perhaps, is to install a cigarette lighter instead of a socket for a portable lamp. For those who don’t know, it’s located a little below the immobilizer. It already has a permanent “plus”, you just need to remove the socket (don’t forget to disconnect the battery), slightly increase the diameter from 25mm to 26mm and install an additional cigarette lighter in the socket. Another method demonstrates how you can install a cigarette lighter in a VAZ 2110 tunnel. In stores you can find a cigarette lighter kit with a hinged cover, wiring and a fuse. Secure it to the tunnel using the self-tapping screws that also come with it. If there is a need to install several cigarette lighter sockets at once, then you can use Chinese tees with wiring. For example, cut off the connector and simply solder it to the wire of the standard cigarette lighter. Route the wiring into the glove compartment, where you can place the tee socket.

Placing a second cigarette lighter next to the standard one or under the immobilizer is also not a problem:

Additional cigarette lighter in the trunk

Those who read the configuration of foreign cars may have noticed the item: a second cigarette lighter in the trunk of the car. It acts as an outlet into which you can connect various devices that may be useful on the road.

Why do you need a cigarette lighter in the trunk of a car? Many people use a car vacuum cleaner, compressor, refrigerator, inverter, flashlight, etc.

The connection of the cigarette lighter in the trunk is similar (in parallel with the standard one or separate wiring from the battery through a fuse).

Either a regular cigarette lighter or a tee, which was discussed above, can act as a socket in the trunk.

Just like that, somehow.

Images

As an option, for connecting different consumers, a pump, a 12V mini washer, etc.

Power source - flashlight - Berkut SMART POWER SP-4L https://emporia-auto.ru/auto/show25176.html

I also had a problem with this infection. The antenna shorted to ground when I inserted the adapter from the recorder, and this antenna burned to the body and when I tried to change the fuse, the new fuse immediately burned out. What’s unpleasant is that the dashboard and immobilizer are powered from the same fuse, so it’s impossible to start the engine (forward to the designers). I picked out this unfortunate tendril and that’s it. By the way, in the service department for replacing the cigarette lighter (the antenna was broken off, it was torn apart) they broke it as much as 5 pieces - they say to disassemble the dashboard and drain the antifreeze.

This cigarette lighter, by the way, is called “Euro”. They do everything through F, however.

The green ring should sit on the backlight fuse. If the cigarette lighter fuse is not in order, then the instrument panel would not light up - it’s immediately noticeable.

I wanted to create a topic, but I'll ask for advice on this one. I needed a permanent plus in the salon. I sat over the cigarette lighter for 1.5 hours, but was still unable to pull its socket out of the panel. I tried to reach inside with my hand and press harder, to grab it from the outside, to turn it in some direction - nothing helped. I couldn't find any similar topics. Somewhere on the Internet I came across information that you need to bend some kind of clamp inside the socket. I tried it - I shortened the plus and minus, burned the fuse, tore apart some internal petal in the cigarette lighter - but it still sits in its place. In this regard, 2 questions - how to remove the cigarette lighter socket and which cars have the same sockets as the Grant? Kalina, Priora, Ten or the same everywhere?

Connecting the cigarette lighter

Never connect the cigarette lighter to the ignition switch. The ignition system will not withstand such a load. Having laid the wire in the engine compartment, bring it to the positive terminal of the battery, connect the fuse and then attach it to the terminal. If for some reason you cannot do this, run a wire with a fuse to the starter and attach it to the positive terminal of the relay. Strip the end of the wire at a distance of 1 cm, place it on the terminal, then crimp it using pliers. Be sure to secure the wire so that it does not dangle anywhere. To attach the wire to the cigarette lighter, use a soldering iron or an appropriate terminal, depending on the device model. Install a fuse and a switch next to the cigarette lighter, this will increase the safety of using this device.

Relay block Lada Granta

The relays are located in the same fuse and relay box, which is located to the left of the steering column under the cover.

K1 - heater fan relay

K2 - power window relay . If they do not work, also check fuse F2; if this does not help, then the problem may be in the control unit.

K3 - starter relay . If it does not work (does not turn) and this relay is working, check the battery charge level. It could also be a problem with the retractor or the ignition switch and its contacts.

K4 - ignition switch terminal 15 relay

K5 - turn signal and hazard warning relay . If the turn signals come on and do not turn off, this relay may be shorted. Also check fuse F3 (emergency mode).

K6 - windshield wiper relay . Check also fuse F4.

K7 - high beam relay . Also check fuses F14 and F15 and the lamps themselves.

K8 - horn relay . Also check fuse F20, signal switch contacts on the steering wheel.

K9 - low beam relay . Also check fuses F12 and F13 and the lamps themselves.

K10 - rear window heating relay . If the heating does not work, the problem may be in fuse F8.

K11 - engine control unit relay . Also check fuse F1.

Installation recommendations

A good splitter will have a built-in fuse, and only such models are worth paying attention to. The tip of the central plug is preferable to a conical one: this will definitely not cause problems

Let's imagine the ordinary everyday situation of the owner of a Lada Kalina. Suddenly it turned out that the cigarette lighter was not working.

What to do? It is the cigarette lighter itself (from which the cigarette is lit) that often stops heating to the desired temperature. In this case, you need to remove the cigarette lighter fuse and move the socket contacts further away. Quite often, in the case of a non-working cigarette lighter, it is enough to simply change the fuse. This is done like this:

• carefully open the fuse box (the cover of the block on the Lada Kalina is made under the side light switch);
• there is a hint on the cover with a diagram of the location of the fuses; We find the one we need, take it out with plastic tongs and insert a new one.

The cigarette lighter fuse in Kalina is located on the 2nd row in the 7th place of the block. You can even install an additional cigarette lighter; on the VAZ 2119 it is powered by the glove compartment light bulb. When performing this procedure, you should be careful when pulling the necessary wires and not mix up the polarity of the contacts. The light bulb has a permanent plus, which simplifies the matter. The socket from it must be removed, first disconnecting the battery.

Read more: How to connect a horn to an amplifier

Power is supplied to the lamp when the low beam is turned on, and in this way you can connect the DVR. The cigarette lighter will fit from a VAZ 2110. You will need 60 cm of wire with two terminals and a 29 cm pen from a screwdriver. There is almost nothing to disassemble. The wire is inserted into the hole of the removed lamp, fished out with your finger under the dashboard, there is a hole there. You can also catch it in the hole on the side of the front passenger door.

Next, you will need a rigid wire that is inserted into the hole in the end switch. One wire is connected to the light bulb, the other to the end switch so that the power is not interrupted. If the cigarette lighter spiral burns out on a Lada Kalina, the easiest way is to install a new one. Remember that the cigarette lighter, such as it is now, arose not so long ago, and switching a large current is clearly not a job for such a primitive device.

Some cars do not have a cigarette lighter, but a full-fledged 12-volt socket, but the Lada Kalina is not one of these vehicles. Also, when driving, the contact between the equipment plug and the socket may disappear. There's nothing you can do about it. Sometimes you have to press the cigarette lighter antennae: over time, they stop fixing the coil and it doesn’t heat up. That's all. Good luck!

Instructions for removing the cigarette lighter of 2nd generation Grants or Kalinas are available in some publications on the repair and operation of these cars. There, to remove the cigarette lighter, the center console is dismantled, but this is not necessary. There is an easier way.

FakeHeader

Comments 26

Yes, it is extremely difficult to remove the cigarette lighter; it took me about 1 hour.

I threw out the standard cigarette lighter because it was causing problems and installed one from a VAZ-2115 and everything became OK.

Now you'll have to insert it for a week. I also changed it on the sedan, there's already a socket on the elevator from the factory. Of course, I had to struggle, but somehow I managed it in about 30 minutes.

explain it to the stupid person. I've already seen 10 of these. Unfortunately, there is not a single topic with detailed photos, especially what’s inside in the so-called outlet itself. Question - how is this different from a cigarette lighter? So you can’t light a cigarette or what? What can be plugged into this outlet? what shape is the nest?

As far as I know, the socket is deeper than the cigarette lighter and slightly smaller in diameter

explain it to the stupid person. I've already seen 10 of these. Unfortunately, there is not a single topic with detailed photos, especially what’s inside in the so-called outlet itself. Question - how is this different from a cigarette lighter? So you can’t light a cigarette or what? What can be plugged into this outlet? what shape is the nest?

This socket is longer than the standard cigarette lighter, so the devices plugged into it seem to sit more securely...

I had to somehow remove this cigarette lighter, I couldn’t, I tried to pull it out for half an hour, I even disassembled the center console, tore off all my hands, only one edge, top or bottom, comes out. How do I get this bitch out? I did everything according to the manual, of which there are plenty. Do the terminals and everything fit into the new outlet? all OK?

Cigarette lighter fuse on Priora

Not so long ago, a cigarette lighter was a mandatory attribute of the interior of any car. Its very name indicates its direct purpose - lighting cigarettes, although for the most part it is not used for this, but for connecting various electrical devices. This could be a car vacuum cleaner, refrigerator, compressor, navigator, DVR, etc.

Today, some modern foreign cars are not equipped with such a device as standard. The place of the cigarette lighter is taken by various kinds of sockets and connectors, with which you can connect and charge anything. You just can't light a cigarette.

Cigarette lighter

The domestic auto industry is in no hurry to replace the cigarette lighter with sockets, so all our cars are equipped with its classic version. Lada Priora is no exception. Here it is located in a place of honor - the central floor tunnel, next to the parking brake handle.

This arrangement of the device was not chosen by chance. It is always in sight, you can reach it with your right hand without bending, it does not interfere, and it is impossible for your pant leg to get caught on it. For greater convenience, it is also equipped with a backlight, which makes it easier to find in the dark.

It is worth noting that the Priora’s cigarette lighter differs from previous models not only in location, but also in configuration: its socket is somewhat smaller than that of other VAZs.

Design and operating principle

The Priora's cigarette lighter is no different from the cigarette lighters of other cars. Structurally, it consists of a socket (a hollow metal cylinder) and a metal cartridge with a nichrome spiral inside.

The cartridge is equipped with a plastic button, when pressed, the “plus” is connected to ground through the spiral.

Its task is performed by bimetallic “ears” inside the cartridge, which, when heated, expand, and the spring ejects the cartridge, setting it to its initial position.

Malfunctions

Like any other electromechanical device, the Priora cigarette lighter tends to break. Sometimes this can be caused by design defects, sometimes by malfunctions in the machine's on-board circuit, and sometimes by the fault of the user himself. Common cigarette lighter malfunctions include:

• sinking of those same bimetallic “ears”;
• burnout of the spiral;
• broken contact in the connector;
• fuse blown.

Malfunctions can also include the burnout of a backlight lamp, however, this is more related to a decrease in the level of comfort than to serious breakdowns. In addition, it does not in any way affect the operation of the device itself and can be easily eliminated by replacing the lamp.

The sinking of the lugs is characterized by the lack of fixation of the cartridge in the pressed position. It can be caused either by the low quality of the metal from which they are made, i.e. defect, or high intensity or long period of use of the cigarette lighter.

How to replace a lamp in a cigarette lighter?

The socket is equipped with a backlight, which is very convenient. However, the lamp may burn out, after which it must be replaced with a working lighting element.

Let's take a closer look. How to do this in LADA Kalina?

1. Following safety traditions, we disconnect the battery.
2. We find a fuse block from which it is necessary to remove the fuse-link marked “F20”.
3. We “defeat” the screws that are designed to hold the transmission lever casing and the tunnel. For ease of operation, we recommend moving the transmission to the 4th gear position.
4. Now you need to pry the device, applying force to the green filter, after which it “comes out” out.
5. To disconnect the clamps, you will need to turn the element clockwise.
6. We proceed to dismantling the metal base.
7. Next, the housing must be removed (painted green).
8. We detect a cartridge. Naturally, there is a lamp in it.
9. Finally it can be replaced.
10. We carry out the assembly, of course, in reverse order.

How to remove the cigarette lighter on a Grant

First of all, as when working with any component of a car's electrical equipment, you need to turn off the power to the battery and only then proceed to remove the cigarette lighter. Carefully bend the edges so that the plastic protrusions do not interfere, and release the metal cylinder. Then you need to remove the center console of the torpedo.

Video of removing the Granta center console

After that, use a screwdriver to press the top latch on the green plastic case and try to pull the base of the cigarette lighter out a little. Now you need to try to disconnect the connector and completely pull out the Granta cigarette lighter.

Repairing a burnt out cigarette lighter

Sometimes it is not necessary to change the Lada Granta device. You can carry out the repair yourself. After removing the device, it is worth inspecting the condition of the contacts. The fallen wires should be soldered, and the oxidized contacts should be treated with a needle file. After this, the device can restore functionality.

Inside the cigarette lighter there is a small mica plate. This is a semiconductor that often fails. It needs to be removed. After this, it is worth assembling the device and then checking that it is working correctly.

How to properly remove the cigarette lighter on a Lada Granta

The presented photo report will show how to remove the cigarette lighter on a Lada Granta in order to replace or repair it. You will also find out why the cigarette lighter fails.

Why does the cigarette lighter on the Lada Grant fail?

One of the main reasons for the failure of the Lada Grant's cigarette lighter is a short circuit, which can occur as a result of a malfunction in the vehicle's on-board network or due to wear of internal elements. Also, removing the cigarette lighter on a Grant is also necessary to replace a burnt-out diode (light bulb) for lighting the socket.

Which cigarette lighter to buy

If you are unable to find the original Granta cigarette lighter, then an excellent alternative would be a spare part manufactured by catalog number DA5100F0109

How to remove the cigarette lighter on a Grant

First of all, as when working with any component of a car's electrical equipment, you need to turn off the power to the battery and only then begin to remove the cigarette lighter. Carefully bend the edges so that the plastic protrusions do not interfere, and release the metal cylinder. Then you need to remove the center console of the torpedo.

how to remove, replace and causes of malfunction

The cigarette lighter in a car is important not only for drivers who smoke; it can serve as an additional power source for various devices and appliances. However, like any mechanism, it can break. The article discusses its structure, purpose, and gives instructions on how to remove the cigarette lighter on Kalina, Grant and install a new one.

Design and purpose of the cigarette lighter

The device is designed simply:

• metal cartridge with a nichrome spiral;
• button;
• plastic handle.

There is a special socket on the dashboard into which the cigarette lighter is inserted. When you press the handle, the device connects to the vehicle's on-board network. A current passes through the nichrome spiral and it heats up. As soon as the temperature reaches its maximum, the thermostat is activated, a click occurs, and the cigarette lighter returns to its original position.

Heated coil for lighting

In the first car models, the device was used directly for lighting cigarettes, but with the development of technology its use has expanded significantly. Currently, all external electronic devices are connected through it: vacuum cleaners, navigators, chargers, radar detectors, mobile phones.

Today, the 12-volt socket of a car has become indispensable; its breakdown immediately causes a number of inconveniences.

Typical faults

The reasons why the cigarette lighter does not work can be different. One of them is a blown fuse. It may burn out due to connected devices, such as a compressor or splitter. To eliminate the problem, you need to open the mounting block, remove the burnt fuse and insert a new one. A regular 15 or 20 Amp fuse will do.

The second no less popular malfunction is the antenna contacts that are bent inside the device. If you use the charger frequently, the metal tendrils will unbend over time. To return the device to functionality, the antennae should be slightly bent using a flat-head screwdriver (video author: Andrei Che).

Repair and replacement instructions

If the reason is not the fuse and the antenna, then the device may not work. In this case, it needs to be replaced. Replacement is complicated by dismantling the plastic floor tunnel.

The replacement procedure for the Lada Kalan and Lada Granta Liftback is similar and consists of a sequence of actions:

1. First of all, you need to remove the battery terminal.
2. Then unscrew the three mounting bolts that hold the plastic handbrake lining.
3. Next you need to unscrew the handbrake switch.
4. At the back of the tunnel there is a self-tapping screw, which we unscrew in the next step.
5. Then we unscrew the fastenings of the floor tunnel from the side.
6. Next, remove the cover from the gear shift knob.
7. Now you can lift the tunnel and begin replacing the cigarette lighter.
8. Before replacing, you must disconnect the power.
9. Next, press the latches that hold the cigarette lighter, and you can remove it.
10. We insert a new part and perform the reverse assembly steps.

Replacing a broken cigarette lighter is simple; any car enthusiast can handle this procedure.