Garage metal prefabricated weight

On average, the weight of a 3x6 metal garage varies between 3-4.5 tons. You may only need information about how much a garage weighs in 2 cases:

You haven't yet decided which metal garage you're going to buy.

In this case, the weight of the metal garage will affect the cost of delivery and the load that the concrete base will receive. If you purchase a garage box from a specific manufacturer, then all the necessary information can be found in the delivery note.

You have decided to move your old metal garage to a new “place of residence”.

In this case, it is quite difficult to know the exact weight of a 3x6 metal garage, since many people cook it themselves. In this case, various material options are used - from various configurations of corners to metal thickness varying around the entire perimeter.

If you are faced with the 2nd situation, then using our method you will quickly calculate the approximate weight and be able to choose the right manipulator.

89517738015, 7776405

* The weight of the garage floor is taken into account.
The estimated weight of an iron garage may differ slightly from the actual one

How to find out the mass of a metal garage . A sheet metal garage usually has a wall thickness of 2-3mm, but in some cases old Soviet garages can be made of thick metal, 4-5mm thick.

Transportation of iron garages on a manipulator in Chelyabinsk and the region.

How much does a garage weigh? Very often when transporting metal garages, the question arises: how to find out the weight of a garage or a shed? Added: Mass calculator.
How to transport an iron garageTransportation of a garage in Chelyabinsk and the region on a manipulator. What garage sizes are suitable for transportation? Transportation of a garage measuring 6 x 2.45.

Thank you, I found out the weight of the garage for transportation

How accurately does it determine the weight of the garage?

with such parameters it definitely won’t work, but it’s enough to choose a manipulator or crane for transporting a garage

How much does it cost to transport a 6x3 garage from ChMZ to the north-west?

Here, after all, the walls and roof, the floor are not included in the calculation?

The area and mass of the floor, walls and roof of the iron garage are calculated. Frame, gate, base, extensions - the weight is only approximately at your discretion

On what basis can the structure be placed?

As noted earlier, the prefabricated Izhora garage is lightweight. Therefore, it does not require capital arrangement of the foundation. In order for the garage to serve you for a long time and not lose its technical characteristics, it is recommended to place it on a concrete base. Those who neglect this advice are faced with the problem of corrosion on the metal base of the building.

Before you begin installing the Izhora garage, you must:

Prepare the area: remove all bushes, large debris, branches, stones from the place you have chosen.
Make a small depression in the soil to lay waterproofing, then you can install formwork and make a frame from reinforcement.
Form a screed, the height of which should be 10 centimeters above ground level. This way you will protect the garage from excess moisture that will come from the ground. The screed should be left until it dries completely.
In order for the walls to be firmly fixed to the base, it is worth making a bottom trim. Weld metal corners and profile pipe. Before laying the trim on the base, lay sheet waterproofing.

If you are installing such a collapsible garage temporarily or plan to dismantle it in the future, it is better to use bolts rather than welding to secure the parts together.

After you have thoroughly prepared the base for the garage, you can proceed directly to its assembly.

How much does a 3x6 metal garage weigh? The answer is in the article!

On average, the weight of a 3x6 metal garage varies between 3-4.5 tons. You may only need information about how much a garage weighs in 2 cases:

You haven't yet decided which metal garage you're going to buy.

You have decided to move your old metal garage to a new “place of residence”.

If you are faced with the 2nd situation, then using our method you will quickly calculate the approximate weight and be able to choose the right manipulator.

Approximate calculation of how much a 6 by 3 meter metal garage weighs

Weight of a metal garage 3x6

Initial data: length 6 meters, width 3 meters and height 2 meters. The basis of the design is an all-welded type of garage, in which a layer of sheet steel with a thickness of about 4 mm (the most common option) acts as a cladding. These are the minimum standard garage sizes for any modification of a passenger car.

Important: How much an iron garage weighs will mainly depend on the thickness of the sheet covering and the total surface area. The basis of the structure for passenger cars weighs at least 2 tons. The roof covering itself will be 1-1.5 tones. The remaining weight is provided by racks and shelves that are installed inside.

Briefly, for the calculation, do the following: Calculate the volume of the garage box by multiplying the length, thickness and height along the axial dimensions. Then, knowing the volume values of the roof and wall, you multiply the resulting figures by the specific gravity of the sheet metal. As a result, we get a weight that will differ by 5-10 kg from the real one.

A direct example of calculating the weight of a metal garage

We count all the elements one by one:

Area of side walls: 2*6*2 pieces = 24 sq.m.
Area of a 2-pitched roof, taking into account the small overhang of the canopies: 2 * 1.9 * 6.2 * 2 sides = 47 sq.m.
We calculate the area of the rear and end walls together with the gates: 3*2*2 pieces = 12 sq.m.
The approximate area of 2 triangular pediments is 4-4.5 sq.m.
If there is a metal floor, we also calculate its area: 3*6 = 18 sq.m.
We add up all the obtained values: 24+47+12+4+18 = 105 sq.m.

How to calculate weight yourself

Calculation of the final mass of a metal garage, the dimensions of which are 3x6 meters, is carried out according to the following algorithm:

Calculate the area of the side walls. The area of one wall is 2*6=12 m2. We multiply the resulting value by 2 and get the total area of both walls - 24 m 2.
Calculate the roof area. We take into account that the roof is gable, and its dimensions slightly exceed the dimensions of the building due to the canopies. The area of one slope is: 2 meters * 1.9 meters * 6.2 meters = 23.56 m 2. The area of two slopes is 47.12 m2.
The area of the front wall, including the gate, and the rear wall is 12 m2.
The gables that form the roof of the building have an area of 4 m2.
Some garages have metal floors. In this case, its area is 18 m2.
Now we know all the data, all that remains is to add them together: 4 + 12 + 18 + 24 + 47 = 105 m2.

The weight of a metal garage - what needs to be taken into account when calculating

The weight of an iron garage depends on many parameters that must be taken into account when calculating the weight of the structure.

An iron garage is an inexpensive and fairly reliable shelter for a car. It will solve many pressing problems: it will hide the car from bad weather or the hot sun, accidental damage and prying eyes; you can carry out simple car repairs, diagnostics or other preventative work in it.

Usually, few people think about the weight of a building, but sometimes a situation arises when a car owner needs to know the weight of a metal garage, so in this article we will talk about the types of metal garages and provide calculations for buildings made of different facing materials.

Types of metal garages

All-welded metal garage.

Garages that have a frame made of steel structures (see Frame garage: how to build it yourself) are considered metal, although they can be sheathed with various materials.

They are divided into two types:

All-welded structures are assembled from sheet steel and all elements are connected by welding. Such a garage cannot be disassembled and can only be transported in assembled form. An all-welded garage can be installed anywhere, it is particularly reliable against penetration and has strong connections.
Prefabricated garages have bolted or anchored connections of parts; the structure can be disassembled and transported in a compact form. It is recommended to install this type on the territory of a personal plot or in a country house, not far from the house, so that there is supervision, since it has poor protection against burglary.

A prefabricated garage made of metal plates, assembled using bolted connections.

Important! In turn, prefabricated structures can have different cladding, and this also determines how much an iron garage weighs.

The following materials are used for lining the walls of the structure:

All these materials have different weights, so when determining the weight of the garage as a whole, this must be taken into account.

How to calculate the weight of a garage

Garage made of painted corrugated sheet metal.

Data on the weight of the transported structure may be needed in the following cases:

When purchasing a garage and delivering it to a permanent location. If the building was purchased from a manufacturer, then the seller provides data on the weight of the order, but when the garage is purchased second-hand, then in this case the weight is often calculated by the buyer.
When transporting a garage to a new location (owner moving, sale, garage for demolition, etc.). If the structure was built with your own hands, the owner may not know its true weight.

For a sample, we will calculate the weight of a metal garage 3 x 6 x 2 m2 (width x length x height) of an all-welded type, in which the lining is sheet steel 4 mm thick. This is the minimum standard size into which almost any passenger car will fit, well, except for minibuses.

Technical characteristics: dimensions and weight

In the production of Izhora garages, durable and proven sheet steel is used. Its thickness can vary from 1.5 to 3 millimeters. To fasten different elements together, you need to use special M 12 bolts. To prevent the garage from corroding, all its elements must be primed and painted.

The average weight of the products is 1300 kilograms. Therefore, they can be easily transported to the assembly site using lifting gazelles. Garages were produced in two modifications with dimensions: 3x6x2 and 3.3x7x2.

The Izhora garage includes the following sections:

13 pieces of straight sections with curved edges on both sides;
2 end sections;
2 sections with hinges for gates;
3 gate sections;
2 corners for gates;
4 front sections;
14 roof panels.

In total, this design kit contains 34 sheets of metal and special fasteners.

Prefabricated concrete garages (concrete garage)

We offer three types of Concrete garages with a width of 3200mm, 3420mm and 3900mm, length 6000mm. height 2600mm.

Surely many motorists have had to deal with the problem of arranging a parking lot for their vehicle. Many people prefer to use paid guarded parking lots, however, there are also some car owners who, for various reasons, want to have their own garage. In addition to its direct functions, a garage is also attractive because it can store various equipment and accessories for a car, and carry out minor repairs, which is very difficult in a parking lot or garage complex. One of the most popular today are reinforced concrete garages.

From a technical point of view, a reinforced concrete garage is a structure made in the form of a monolithic box. Since reinforced concrete structures are quite heavy in weight, it is quite natural that prefabricated reinforced concrete garages are especially popular, the delivery of material for which in parts is most economically beneficial for the buyer. Often, for a buyer who has studied the market, it becomes quite obvious that buying a reinforced concrete garage is much more profitable both economically and in terms of labor costs compared to building a garage from other materials. This design has many advantages: quick construction, convenient transportation to the assembly site, no welding work, the ability to quickly dismantle and transport to a new location.

Interesting facts and main advantages

The first prefabricated Izhora garages began to appear in the early 50s. They got their name from the location of the metallurgical plant on the Izhora River. Since then, these designs have been in incredible demand among car owners. Let's take a look at the main advantages of garages, their technical characteristics and structure assembly diagrams.

Let's start our review of such structures with their main advantages. These include:

simplicity and efficiency of assembly;
the ability to dismantle the building at any time;
light weight, therefore, there will be no need to make a capital foundation for the garage;
strength and resistance to negative environments;
the ability to use the structure not only as a garage, but also as a workshop or warehouse.

How much does a garage weigh | Rental of special equipment in Chelyabinsk

Very often, when transporting metal garages, the question arises: how to find out the weight of a garage or change house?

Added: Garage weight calculator

To do this, you need to know the volume of metal from which the garage is made. Below is the frame and dimensions of a typical 6x3m oversized garage.

Let's calculate the area of all the walls of the garage:

roof including slope and canopies: 2*(2*1.9*6.2) = 47m2
side walls 2pcs: 2*(2*6) = 24m2
floor: 6*3 = 18m2
back wall and gate: 2*(3*2+2) (triangle) = 16m2

Total area of the entire surface of the garage: 47+24+18+16 = 105m2

Now let’s calculate the volume of metal, with a garage wall thickness of 3mm

The mass of 1m3 of metal is on average 7900 kg, hence the weight of the garage lining

0.315*7900 = 2500 kg

But this is only the sheathing; the frame of corners and gates weighs about 1000 kg.

The total weight of the 6x3m garage is at least 3500kg.

If the wall thickness is 4mm it will already be 4300kg.

Thus, iron garages usually weigh from 2-3 to 5 tons.

Instructions for assembling an Izhora garage with your own hands

Before you begin the assembly process, invite a friend to help you. Because it is difficult to cope with such work alone. Be sure to prepare all the necessary tools and supplies. The tools you will definitely need are:

hammer;
sledgehammer;
box wrench;
locksmith's beard.

There are two ways to assemble such a structure.

1st method (for this assembly you must invite a friend):

Begin assembling the end wall sections.
Assemble the side sections together.
Cover the walls with a roof.
Install the gate.

Method 2 (you can do it yourself):

Start installing the garage from the back wall.
Add side panels to the end.
Attach the roof next to the side panels.
Finish the assembly by installing the gate.

Adviсe

Shells are very convenient and compact. To make them even better, you can use additional tips.

So, for example, car enthusiasts who spend a lot of time repairing or tuning their cars will like the idea of at least a little insulating the garage. To do this, you need to sheathe it from the inside with panels. The classic heating option is unlikely to work here.

It is not worth saving on the insulation of a structure in the same way as on its protection. The anti-corrosion coating chosen to protect the metal must be of high quality so that the building lasts longer. If the shell is placed in a place with a cold or rainy climate, the protective layer will need to be renewed over time. Not only the appearance of the garage, but also the level of security of the car depends on this.

And finally, before installing a “pencil case”, especially in the city, it is worth checking again how legal it is. Laws change over time. To be sure that the new building will not be forced to be demolished or moved to another location, you need to clarify what rules are in force now.

The following video provides an overview of the shell carport.

How to extend the service life?

In order for the garage you installed to serve you as long as possible, you should definitely prepare the surface before installing it. It is also important to take into account that a structure installed on swampy soil will become unusable much faster. It is best to install such buildings on hills and in dry areas.

To make your garage look attractive from the inside, you can use clapboard or plywood. You can lay linoleum or rubber flooring on the floor.

To summarize, it is worth noting that the Izhora garage is the most affordable in financial terms. It is perfect for installation in a country house or in a private yard. If you carry out the preparatory work correctly when installing it, then this design will serve you for many years. And if you add sections to the standard package, the garage will become more spacious and convenient to use.