Bolt pattern of rims and wheels on the VAZ-2112: parameters, photos

Not every beginner who gets behind the wheel of a VAZ-2114 car is able to choose the correct size of wheel rims. And this important detail of a VAZ vehicle requires the right approach and constant attention.

This element of the machine contains brake pads that require replacement at a certain time. The duration of roadworthiness largely depends on the type of driving. Also an important task is the competent selection of each component based on the compatibility of individual spare parts. You should always listen to the advice and recommendations of the VAZ manufacturer regarding the installation or replacement of additional accessories.

For example, factory wheels that have a factory bolt pattern are equipped with the appropriate components. It is strongly not recommended to change the latter to others.

If a car enthusiast has “itching hands” and wants to use other spare parts not provided by the factory for the VAZ-2114, such actions must be discussed with a specialist.

Standard wheel sizes VAZ 2110 1.5i 2110x

The VAZ 2110 1.5i 2110x model was produced from 1998 to 2004. Table of standard and suitable wheel sizes for VAZ 2110 1.5i 2110x.

Disc drilling parameters are usually called bolt pattern:

• LZ (number of holes)
• PCD (hole center circle diameter)
• ET (disc offset)
• DIA (hole diameter)

Useful articles and reviews Announcements of certificate drawings among subscribers. Subscribe to VK group

Despite the fact that this information is taken from the websites of auto manufacturers, our catalog is for informational purposes only and does not guarantee full compliance of the proposed sizes with your car.

What tire sizes does the manufacturer recommend to install?

The standard size depends on the body type. Moreover, all cars without exception used discs with a hub diameter of 58.5 mm. The amount of overhang could fluctuate - within 37-40 mm. The rim width is also typical - 5-5.5J. The most common model is 2110. This digital combination is used to mark a car with a sedan body.

The manufacturer recommends the following sizes:

• 2110, 21101, 21102 – 175/70 R13;
• 21103, 21104 – 175/65 R14.

"Razboltovka" - 4x98 mm. A special modification is the VAZ 21108 Premier car. The car was produced for a relatively short time - from 1999 to 2001. The only difference from previous versions is that alloy wheels with a diameter of 13 inches were installed at the factory. There are no fundamental differences for station wagon cars.

The issue was carried out between 1997 and 2004. The wheels installed at the factory differed depending on the modification of the car and the marking of the specific model:

• Lada Priora wheel sizes, rims, tires

• 2111 – 175/70 R15;
• 2111i-2114 – 175/65 R14.

Hatchbacks were produced, like most other cars in this series, until 2004. The diameter of the wheels and their dimensions also differed slightly depending on various factors:

• 2112 – 175/65 R14;
• 21122 – 175/70 R13;
• 21124 – 175/65 R14.

Using tires of standard size and diameter will avoid damage to the body and other troubles. However, the automaker suggests the possibility of installing custom-sized wheels.

Theory

So, number 4 is the number of bolt holes. And the second number is the diameter in mm of the circle in which they are located. It is not so difficult to calculate that the distance at which the bolt is located from the bolt, if the bolt pattern is 98, will be 69.3 mm.

This is the same value for all wheels installed on the VAZ 2110. But in foreign cars, most of which have a bolt pattern of 100, one bolt from the other is located at a distance of 70.7 mm.

The difference is 1.4 mm, and this will no longer allow ideal installation of wheels with a bolt pattern of 4x100 on a VAZ 2110.

The difference between the bolt pattern 4*98 and 4*100

Main characteristics and varieties

The rear wheel bearing on the VAZ-2108 is produced under catalog number 256706. It has the following technical characteristics:

• weight, g - 400;
• number of balls, pcs. - 28;
• ball diameter, mm - 9.525;
• static load capacity, KN - 25.9;
• dynamic load capacity, KN - 30.1;
• rated speed, rpm - 6500.

The VAZ-2108 rear wheel bearing number may be different. If a store offers you a product marked 537906, don’t be surprised. This is a high-load bearing. Some of its characteristics differ from the characteristics of the standard spare part:

• weight, g - 511;
• static load capacity, KN - 90.1;
• dynamic load capacity, KN - 64.8;
• rated rotation speed, rpm - 5000.

As you can see, the reinforced rear hub bearing on the VAZ-2108 has increased resistance to loads. But at the same time, its rotation frequency should not exceed 5 thousand rpm. Such products, when properly used, can “walk” freely up to two hundred thousand kilometers.

Installing 4*100 disks

Let's consider several methods used by car craftsmen to install disks from foreign cars on a VAZ 2110:

1. Sometimes holes are drilled into the disc hub on a lathe so that it will be possible to install the discs you currently have. Both 98 and 100 bolt patterns are suitable. And if you need to replace the disk, then this is also not difficult to do. The bolt sizes are standard;
2. The simplest, but not the best way is to install the disk using extended bolts of regular diameter for wheels. But don’t be surprised later that this replacement led to the disc dangling, wheel play appearing, and it is impossible to establish the correct camber and toe, as well as the longitudinal inclination angles;
3. A popular, relatively safe method is to install standard size bolts with an eccentric on a VAZ 2110 (an option is also possible if the bolt has an offset center). Today, online stores offer many sets of such bolts;

Wheel bolt with eccentric

If you replace the standard wheels of a VAZ 2110 with those with a 4x100 bolt pattern, then when you gain speed you will find that the wheel dangles, and during sharp braking it may even fall off, and how this “adventure” will end is unknown.

Bearing sizes

The article contains a photo of the VAZ-2108 front wheel bearings, as well as a drawing of a puller indicating all dimensions. Therefore, if you are in doubt whether you purchased the right roller, check the dimensions of the hub. The part number is 256907.

The dimensions of the element are:

1. The outer diameter of the holder is 64 mm.
2. Inner diameter - 34 mm.
3. Weight - 445 g.
4. Balls with a diameter of 9.525 mm are installed inside.
5. The total number of balls is 28.
6. The unit is designed to operate at rotation speeds above 6000 rpm.

In any car store, salespeople will be able to advise you on the best quality product.

Wheel alignment

After replacing wheel rims, the dimensions and bolt patterns of which differ from those provided for by the design of the VAZ 2110, it is necessary to make all the necessary adjustments in order to ensure reliable protection of the entire chassis, as well as tires and arches.

Correct alignment angles are required for each front wheel. There are three parameters that require correct installation: wheel toe, caster angles of the steering axles, and camber angles of each wheel.

Wheel installation options

The rules by which the parameters of the front wheel are set are as follows:

1. You won't go far if everything hangs out the way it wants, and the car is pulled to the side when it should be going straight. To ensure the stability of each front wheel, they are installed strictly at the required angles to the body and suspension elements. This is called the longitudinal inclination angles of the turning axis. Installation dimensions are indicated in the instruction manual;
2. Camber is the angle between the plane in which the wheel rotates and the vertical. The camber bolt helps install it (it secures the telescopic strut and steering knuckle). If the camber is installed incorrectly, the car “steals” and the tire tread wears out more on one side;

Wheel installation options

Rear wheel bearing VAZ-2108: dimensions

As for the size of the wheel bearing, they are the same for both modifications:

• outer diameter, mm - 60;
• internal diameter, mm - 30;
• width, mm - 37.

If you are offered a rear wheel bearing for a VAZ-2108, the dimensions of which do not correspond to those specified, it is better to refuse this purchase. All the above parameters are provided for by GOST 520-2002. Foreign analogues of spare parts are manufactured in accordance with the requirements of ISO 15:1998 and have the same dimensions.

Preparing for adjustment

Most often, the VAZ 2110 camber and alignment are installed at a service station, but you can do it yourself. First of all, check whether there is play in the bearings and whether the steering is loose. At the same time, check the diameter and absence of deformation of the disks, air pressure in the tires, and tread wear.

VAZ 2110 front suspension assembly diagram

Naturally, if a wheel is loose, action will need to be taken, and one with improper tread wear may need to be replaced. Wheels standing on the ground need to be pulled relative to the vertical. If you find any play, have a helper apply the brake and check the play again.

If it disappears, the bearing needs to be replaced. If after this the size of the play not only does not disappear, but only decreases slightly, the suspension needs to be checked, repaired, and sometimes replaced.

Front wheel hub diagram

After this, hang the wheel and check the play again. It is possible that the play has disappeared, but the wheel turns jerkily or is simply difficult, then you need to slightly expand the diameter of the bearing installation site.

If you hear a grinding noise, the bearing needs to be replaced.

What is the tire pressure

It is important to constantly monitor the tire pressure - this will avoid difficulties when operating the car. It should be noted that for different tire sizes the value may differ slightly:

• Maximum wheel size for VAZ 2109. Which wheels and tires to choose

• 175/70 R13: for front wheels – 1.9 MPa, for rear wheels – 1.9 MPa;
• 175/65 R14: for front wheels – 2.0 MPa, for rear wheels – 2.0 MPa;
• 185/65 R14: for front wheels – 2.0 MPa, for rear wheels – 2.0 MPa.

Some drivers deliberately inflate the front wheels below the manufacturer's specified value. Main reasons:

• less load is placed on the suspension;
• minimal feedback to the steering wheel when hitting bumps or other road irregularities.

However, low blood pressure causes:

• deterioration of management;
• quick “grinding” of the tread along the edges of the tire;
• increased gasoline consumption - by 10-15%;
• uneven axle load.

Excessively high blood pressure also causes problems. For example, when heated to 60 degrees Celsius or higher, the wheel may simply burst.

Self-adjustment

Next, you need to stand on a level surface and load the machine, as recommended by the manufacturer. That is, about 320 kg in the cabin and 40 kg in the trunk.

The first adjustment is to set the pitch angles of the turning axis. The second is camber, the third is toe.

In this case, the camber angle in the loaded state should be 0°30'+-30'. The toe-in should be within 0°15'+-10', and the pitch angles of the steering axes should be 0°20'+-30'.

Remember that camber and other wheel adjustments are necessary in all cases when you in any way interfere with the operation of the front suspension of the VAZ 2110.

Instructions for removing the hub assembly from the rear axle

1. We turn off the engine, put the car in gear, and install stops under the front axle.
2. We jack up the wheel we need.

1. We tear off the mounting bolts and remove the removed wheel.
2. Now we have access to the brake drum. Using a “12” wrench, unscrew the pin guides and remove it. The brake drum may be firmly in place. Then WD-40 universal lubricant will come to the rescue. And if the knot is stuck too tightly, you can remove it with a hammer or mallet, gently tapping it around the perimeter.

1. Unscrew the hub nut.
2. We remove the hub using a special two-jaw puller for VAZ bearings. If you don’t have one, you can simply screw the wheel to the axle and then quickly pull it off.

Corrosion protection

For reliable operation of the chassis, everything is important: the bolt pattern, the dimensions of all components, the alignment/camber settings, and even the protection of the arches from corrosion. It is the arches that are more susceptible to adverse factors than other parts of the body - from ordinary moisture during rain to reagents on winter roads.

To ensure reliable protection of the arches, it is best to install lockers (fender liners) on the VAZ 2110. Such protection will cost much less than subsequent repairs of rusted arches. It is important to choose the correct size of the lockers and ensure their tight fit in the area of ​​the arches.

We hope that by completing all the repair work yourself, you will provide your VAZ 2110 with many years of trouble-free service on the road.

Wheel bolt pattern parameters for VAZ-2110

Dull VAZ stamped wheels are often hidden behind elaborate plastic caps. And for good reason. Every owner of a VAZ-2110 wants his car to stand out from the mass of gray and black dozens. One of the ways to improve the appearance of a car is deservedly considered to be replacing the wheels. Not many people think that when selecting a replacement disk, you need to take into account not only the number of mounting holes. Today we will look into the bolt pattern of VAZ-2110 wheels and select several options for a simple and bloodless replacement.

What does loosening mean?

Each wheel rim, like a tire, has its own purpose and its own parameters. The most popular on our roads are steel stampings and alloy wheels.

Basic parameters of the wheel rim.

A competent owner always has in stock not one set of disks, but several. The use of casting is safe and rational only on good and near-ideal roads. In our areas, steel wheels dominate, but they are not all the same. You can select the right replacement disk only by knowing its exact parameters. Only then will it guarantee a safe and comfortable ride.

Wheel bolt pattern parameters for VAZ-2110

Stamped wheel 5.0J14 4×98 ET35 d58.6 for VAZ-2110.

All VAZ vehicles are equipped with rims that meet the so-called “Italian” standard.

And this is not in vain, if you remember the history of the plant. The disk parameters for the VAZ-2110 are as follows: 5Jx13 PCD4x98 ET35-40 DIA58.6 . In order not to get lost in symbols and numbers, let’s look at each parameter in order:

• 5J - means that VAZ cars of the tenth family can have a rim width of 5 inches, with the maximum allowable width being 5.5 inches ;
• 13 or 14 - disk diameter in inches;
• PCD 4×98 - this is the same bolt pattern, which is no more important than other parameters of the disk, it means that the disk has 4 holes, the centers of which are located at a diameter of 98 mm (Pitch Circle Diameter ), a single parameter for all VAZ cars except Lada 4x4;
• ET 35-40 - the minimum and maximum possible disc offset, that is, the distance from the geometric center of the disc to the mating plane of the wheel to the hub;
• DIA 58.6 is the diameter of the disk mounting hole on the hub; this parameter is the same for all VAZ cars (except Lada 4x4).

The exact parameters of the wheel rim must be stamped on it.

Wheel selection rules

For the “ten”, the original wheels are 13- or 14-inch with a 4x98 bolt pattern, where 4 is the number of holes, 98 is the diameter of the circle on which they are located.

In fact, there is nothing complicated about it. It is not necessary to put your life in danger by installing discs with a drill even 1 mm more or less than permissible. Any wheels from Italian and some French cars are perfect for cars of the tenth family. Of course, with the same bolt pattern.

Here are just some of these cars:

• Ford Ka produced after 2009;
• Lancia Delta;
• Lancia Lybra;
• Lancia Musa;
• Lancia Ypsilon;
• Peugeot Bipper;
• Alfa Romeo 145, 146, MiTo;
• Citroen Nemo;
• a huge number of Fiat car models.

Table with bolt pattern 4x98.

It is worth noting that new VAZ cars have changed the Italian size to French. This happened with the arrival of the French B0 platform , on which Vesta, Largus, and Xray are built. Their disc drilling parameter is 4x100 mm. Select the right discs and do not forget about safety!

What wheels were installed on different car bodies and configurations?

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

The factory equipment of the car is limited to the installation of stamped wheels. They have good performance in terms of strength, service life and wear resistance. However, as far as appearance is concerned, there is still room for work.

By the time the LADA 2110 was released, the automotive market was already filled with various alloy wheels of various sizes. The best option is to install alloy wheels, which are attractive and durable.

Before purchasing new disks, you must remember that not every disk may be suitable for a car. The product is selected based on the parameters determined by the vehicle manufacturer. The bolt pattern, the size of the central hole and the nuts that will secure the disk are taken into account.

And that's not all - the territorial conditions (climatic features) in which the car will be operated are also considered, as well as the external data of disks from various manufacturers.

The AvtoVAZ plant installed stamped wheels in black or white with the following standard parameters:

• bolt pattern 4x98, which indicates that the disk model is fastened with four studs, each 98 mm long
• departure ET35

The Ten is a universal model, the wheel arches of which allowed the installation of wheels with dimensions from R13 to R17. Car owners installed beautiful alloy wheels from well-known brands, which made the car even better.

How to understand that it is time to change the wheel bearing

A failed VAZ-2108 rear wheel bearing may indicate a malfunction:

• the appearance of a characteristic hum from the wheel;
• uneven rotation of the wheel;
• backlash formation.

If you notice that there is a hum coming from one or both rear wheels, rush to diagnose the wheel bearings. You can do this right in your garage. Simply jack up the rear wheel and turn it by hand. It should rotate easily and evenly without making any sounds. Next, grab it with both hands and try to shake it from side to side in a horizontal direction. If the wheel rotates unevenly and you feel play when it becomes loose, get ready for repairs.

The main disk manufacturers whose products are set to ten

• Most VAZ 2110 representatives are equipped with products from the Russian manufacturer KiK. The brand is quite popular due to its huge assortment, as well as its design developments in the field of creating discs.

• The next popular manufacturer is Vicom, which produces sports products. The company was created on the basis of the Institute of Metals and Alloys, has its own production technology and produces interesting specimens with twisted colored knitting needles.
• The Krasnoyarsk SKAD plant produces wheels that are exported to other countries. The assortment is not very huge, but due to the mass production of disc models, the plant can set a minimum price for the product.
• Slik products have been supplied to the Russian automotive market for three decades now. The assortment is quite wide, here you can find exclusive items, wheels for high-speed travel and off-road driving.
• The very young brand IFree began its work in 2010 and has gained a certain respect among car owners.

These manufacturers produce products that provide the optimal solution for the driver: an affordable model price and its acceptable quality.

Manufacturers

Many motorists do not know which VAZ-2108 front wheel bearing to choose for their car. Now you can find several manufacturers on the market:

1. GPZ-23, Vologda, has the abbreviation VBF. The plant has earned the trust of motorists and is one of the best manufacturers of wheel bearings for domestic cars. Due to the relatively low cost, these parts are practically not counterfeited.
2. SPZ, Saratov - according to many experts, bearings from this manufacturer are the most reliable, durable and of high quality. And most importantly, the cost of parts is very low.
3. GPZ-20, Kursk is no longer engaged in the production of wheel bearings, but you can find products in stores and warehouses.
4. Experts do not speak very well of the Samara SPZ-3. The cost of the bearings is very low, but the quality is not great, the service life is very short.

Some auto stores try not to deal with little-known companies that produce low-quality products. Therefore, on the shelves you can only find bearings from Saratov and Vologda.

What kind of disks can be installed?

Too huge a range of products can confuse the most experienced auto expert. Therefore, before purchasing a product, you need to familiarize yourself with the characteristics of popular discs, as well as know which countries produce them and are popular. What products are suitable for the LADA 2110 car?

• Domestic production. When creating models, the low quality of the road surface and the significant load on the wheel are taken into account. The product combines durability, reliable design and affordable cost compared to analogues from imported manufacturers.
• China. They became famous for their low cost and poor performance characteristics. At the same time, on the Chinese market for domestic use, there are product samples that are not inferior in their characteristics to well-known global brands. Many car enthusiasts order wheels online, which does not always pay off.
• Türkiye. Pretty good disk options. They have good quality, durability and stylish design. Quite suitable for our roads. As for the cost, they are much more expensive than Chinese and domestic manufacturers.
• Asian countries (South Korea, Taiwan, Japan). They have high technical characteristics and are reliable in operation. But the price of the product is very high.
• European brands and USA. Due to the high cost, wheels from these manufacturers are almost never found on our VAZs.

Types of rims

Which discs are better?
Today Russian discs have become very popular:

• KiK,
• Scud.

Car enthusiasts give a very high rating to the products of the Verkhnaya Salda metallurgical plant, which produces forged models called LS FlowForming.

Light alloy cast products made in Germany are also in great demand:

• A.E.Z.
• Dezent,
• Dotz.

The samples listed above have long been considered classics among car rims.

The Italians delight with their beautiful appearance and attractive design. The most striking of their products are:

• OZ Racing,
• Alessio.

In recent years, Korean products, manufactured in Taiwan, Indonesia, and South Korea, have begun to appear on the domestic market.

It must be said that all these rims differ from their analogues in very high quality. The fact is that for production at factories the latest technology developed by the world's leading manufacturers is used.

Engineers from Japan, Italy and Germany have been developing such a technological process for many years. Therefore, all the nuances and subtleties of production were taken into account. The innovative technology they created enabled Korean specialists to produce only the highest quality products.

When choosing, there are two more points to consider:

1. Front-wheel drive VAZ 2112 cars can be equipped with 5.5x14.6x14 wheels.
2. If a low-profile tire is installed, you can use 6x15, 6.5x15.

However, I would like to warn you that the manufacturer does not allow the installation of r15. Complications may arise during the technical inspection. Tires of this size do not fit all wheels.

Maximum and minimum possible parameters of non-standard disks

The most acceptable option for mounting on a VAZ 2110 is considered to be alloy wheels. When choosing alloy wheels, you need to consider the following parameters:

• R – disk diameter;
• J – rim width;
• ET – indicates departure;
• Dimensions of tires mounted on the rim;
• the diameter of the central hole is 58.5 mm;
• the diameter of the circle on which the bolts are fixed is 98 mm.

All these indicators may vary depending on the selected model. For example, for 13-inch wheels the width ranges from 5 to 5.5 with an offset of 35 - 35. On 14-inch wheels the width increases from 4 to 6, respectively, and the offset decreases from 45 to 35. For 15-inch models the values ​​are different .

Compliance with these values ​​is very important. Otherwise, you can get into a lot of trouble driving your car on the road. A car with small wheels still doesn’t look as stylish or presentable.

Features of disk sizes for “Ten”

The product dimensions listed above are ideal for the VAZ 2110, however, some climatic, operational and other external factors that may affect the operation of the car should be taken into account. All disc features for each radius offered by the manufacturer:

• Wheels on the VAZ 2110 are size 14 - a small wheel radius, typical for simple configurations or for economical drivers who install them to reduce costs. Most often found on the market in a stamped version, however, inexpensive and high-quality specimens can also be found in casting. Starting with a rim width of 6.0J, the wheels are ideal for installing winter tires, since the profile height of 60...65 mm guarantees reliable grip on the side surface of the tire even in deep snowdrifts.
• Wheels 15 by 2110 are the most universal size, at which the driver can safely install high-quality all-season tires and forget about changing wheels every six months for at least several years, depending on the driving style and the annual mileage of the car.

R16 wheels for VAZ 2110

• R16 - most often installed in a cast or forged version for comfortable driving around the city. The tire profile of 55 mm is sufficient for both dynamic driving on smooth asphalt and short trips outside the city on unpaved surfaces.
• R17 - for the VAZ 2110 are exclusive products that are installed exclusively for high-speed driving on high-quality roads. In the cold season, it is better to get another set of rims, since the cross-sectional height of a tire of 45 mm is not enough for safe driving on slippery surfaces.

When choosing wheels, it is important for the owners of the “Ten” to follow the factory parameters of the ET offset from 27 to 35 mm, since otherwise the wheels may touch the wheel arches, calipers or suspension elements, and also if the car owner purchases steel wheels for 2110 with zero or negative departure, then he needs to be prepared for rapid contamination of the side of the body of his “iron horse”.

Important! Exceeding the permissible values ​​may cause additional forces, contributing to sudden deformations and rapid wear of the shock absorbers.

R17 wheels for VAZ 2110

By adhering to the geometric characteristics of the wheels specified by the manufacturer and choosing only trusted suppliers, any driver can be confident in the long and safe operation of his “Ten”. Also, when changing disks, the driver must remember that, while remaining in the same size and model, you should not buy only one wheel, and experts advise changing them in pairs or all at the same time, so that uneven wear does not affect the suspension imbalance.

You may be interested in this About original wheels for Toyota

Answers (3)

Follow the answers to this question

• The standard factory sizes for VAZ 2110 tires are:

  175/70 R13 175/65 R14

  As tuning options, owners install the following tire sizes:

  185/60 R14 195/50 R15 205/45 R16

  The photo shows R14 wheels

  Petr Expert The future lies with AvtoVAZ!

  10/12/2015 at 21:45

• The wheels have a bolt pattern of 4X98, width of 5-5.5J, offset of ET37-40, Tso of 58.5.

  wheelman I know everything about tires and wheels

  11/19/2016 at 22:58

• Here is the table, only the hub diameter is 58.5 mm

  Airat Kadyrmaev I love cars, especially practical ones, my channel on...

  11/19/2016 at 23:02

Similar questions

Ilgiz Safiullin

Lada 2110

This is interesting: What size tires are on Sobol

Working with new disks

Many owners of the “Ten” are interested in which brake discs are best to choose for the VAZ 2110. The question is quite logical. Choose certified replacements from reputable manufacturers such as Bosch, or stay true to factory parts. These are the two best options in terms of quality and compliance with the car itself.

New Some people take similar wheels that partially fit the “ten”, sharpen them, and adjust the design. This is a dubious undertaking, since it requires serious skills in such a matter, additional time and financial costs. At the same time, it is far from a fact that such brakes will work better than those offered by the AvtoVAZ plant.

You've already figured out how to remove the brake element, so it's time to work on a new one. It’s not enough to just buy another brake disc and put it in place. First, it is prepared and a runout check is performed. Let's talk about this in more detail.

• The coating must be removed from a new disc.
• This coating serves as a kind of preservative.
• The layer is removed using any solvent.
• Clean thoroughly and wipe the part dry after finishing work.
• Now you can put the disk in a new place and check the runout.
• The permissible runout is no more than 0.15 millimeters.
• If the value is exceeded, this can lead to an increase in the sensitivity of the brake pedal, as well as the formation of vibrations during braking.

How to choose the right alloy wheels

When choosing suitable rims for your car, you need to take into account certain dimensions:

• Diameter – R,
• Width – J,
• Departure: ET.

The mounting bolts are located along the diameter of the circle. The wheel size on the VAZ 2110 is 98 mm. The central hole should have a diameter of 58.5 millimeters.

When purchasing, you must also take into account the disc offset. Sometimes the length of conventional mounting bolts is short. During screwing, they only grip two or three turns of thread. This is not enough for a good fastening.

The problem can be solved very simply. You need to buy special extended bolts. They will securely fix the wheel.

About wheel bolt pattern on domestic VAZ cars

Reading time: 7 minutes

The engineering staff of any automaker carefully calculates the compatibility and ability of the vehicle to withstand the design loads for all systems. A vehicle of the declared weight and dimensions must satisfy its technical characteristics, dynamic and load-carrying parameters. One of the most critical parts is the wheel hub, which bears at least 25% of all permanent, long-term and short-term loads that act on the car. This is how the wheel bolt pattern parameter is created.

Wheel rim bolt pattern on Lada

Bolt pattern is a calculated characteristic of wheels, which determines the number of mounting holes and the diameter of their location circle. This characteristic is the same for almost all AvtoVAZ models and depends on the following vehicle indicators:

Wheels for VAZ 1111

• The weight of the car in running order, that is, fully equipped, with passengers and the maximum possible weight of cargo in the trunk.
• The nature of the vehicle’s operation, namely how important overloads are for a given vehicle. If we are talking about a city sedan, then a bolt pattern of 4 studs is quite enough for it, but a crossover or SUV is certainly equipped with 5 or 6 threaded rods, because off-road driving can temporarily increase the load on the wheel several times.
• Dynamic properties of the car. When entering a turn at high speed, as well as getting into holes, the impact increases the load on the hub studs exponentially.

Information on wheel bolt patterns on domestic VAZ vehicles

All VAZ cars from the very foundation of the plant to the present day had only 3 main types of bolt patterns, since most modifications were made on a single platform, only their appearance changed. The bolt pattern for most Lada models looked like this:

• The smallest representative of the automaker - VAZ 1111, popularly called "Oka", was produced in the Russian Federation for 20 years - from 1987 to 2008. Considering that the weight of this especially small class car was only 975 kg, and the load on the wheel was less than 250 kg, Oka became one of the few representatives in its class for which a bolt pattern of 3 studs was used.

It was quite problematic to find a similar wheel size on the market, so stamped products with a radius of R12 and R13 were often re-drilled in order to successfully fit on the hub.

Starting from 1966, when the concern released its first “penny”, and ending in 2015, the wheel bolt pattern for these cars was 4x98 mm, the diameter of the central hole was 58.1 mm.

The most popular Lada models today, for which wheels with a 4x98 bolt pattern are still sold, are VAZ 2106, 2107, 2109, 2110, 2112, 2114.

• The latest VAZ models, such as Vesta, Granta and X-Ray, produced since 2015, have a wheel pattern as close as possible to the international standard for compact cars. This parameter on the specified modifications is 4x100.

• Among all the products of the AvtoVAZ concern, such models as the VAZ 2121, or the classic Niva and all derivatives of this SUV have always stood out: the 5-door Taiga, Chevrolet Niva and other models. Due to increased loads on the hubs and wheels due to unsatisfactory road conditions, for which all parameters of the Niva were designed, these compact all-terrain vehicles traditionally had a disc bolt pattern of 5x139.7, with a central hole diameter of 98.5 mm.

These increased indicators allowed the wheel to freely resist bending moment, absorb large loads when the center of gravity is shifted to one side when moving on an inclined plane or when the wheels are forced to hang, and also allowed the car to transmit more torque to the tire treads when driving uphill without the risk of breaking parts .

Wheels for VAZ 2114

Features of wheel sizes for the most popular VAZ models

Among several dozen VAZ modifications, the most popular models over the entire 50 years were only 2 of them, as can be judged by the number of copies sold. The wheel sizes for these cars had the following parameters, which varied depending on the year of manufacture, technical equipment and equipment of the car:

• VAZ is the latest modification of the “classic”, produced on the plant’s conveyors for 30 years: from 1982 to 2012. During this time, it never changed its appearance, and the disc bolt pattern was the same - 4x98 with a central hole diameter of 58.6 mm.