Setting the time on the tomahawk alarm key fob


How to install and adjust the time on the Tomahawk key fob

Perhaps one of the most useless features of remote key fobs is the on-screen clock.
Does it often occur to you to check the time using it? From the “same opera”, the provided alarm clock function – it also cannot be called making much sense. Then it turns out that setting and adjusting the time on the key fob should only be done by perfectionists? In fact, not only: for example, the latest Tomahawk alarm models provide storage of up to 10 recent alarm events. That is, using the key fob you can find out the reason for the alarm and the time of its occurrence. Let's say you have CCTV cameras in your yard - then you can quickly view the recording from the desired time to understand why the missed alarm was triggered.

User manual

In accordance with the operating instructions, the basic functions and timers are configured using the main key fob with a screen. To turn the security mode on or off, press the key with the lock icon on one of the key fobs. The signal LED on the car will blink 1 time per second. To turn on the “Anti-Seizure” mode when the engine is running, you must simultaneously press the security and trunk control buttons on the Tomahawk 434 MHZ Frequency alarm key fob. After 30 seconds, the starter will be blocked and the alarm mode will turn on.

Identification of symbols and buttons

The buttons for turning the security mode on and off and auto-start are located on the front side of the key fob next to the display. The remaining 3 buttons are on one of the side faces of the case. The key with the letter “T” is intended to switch to the mode of setting alarm parameters or switching the backlight of the key fob screen.

The trunk icon button is used to check the alarm status as well as operate the trunk lock. The key with the key symbol allows you to remotely start or stop the motor manually. The sledgehammer icon on the display indicates that the shock sensor is activated. The “Override” mode is indicated by an icon with 2 letters Z. The car icon shows which doors are open.

Programming a new key fob

To link a new key fob to the Tomahawk 434 MHz Frequency alarm, you will need to press the “Override” button seven times, and then immediately turn on the ignition by turning the key. 7 confirmation signals from the standard siren will sound. On the attached key fob, the buttons with the lock and key symbols are held until a single signal from the siren and the communicator speaker appears. After turning off the ignition, 5 light signals will indicate exiting the binding mode.

How to set up autorun

A car with a manual transmission must be prepared before setting up auto start on the Tomahawk alarm. To do this, with the engine running, lift the handbrake lever and press the button with the key symbol on the key fob, after which you should turn off the ignition. To enable automatic start by time, you will need to press and hold the buttons with the key and mute icons. Immediately after this, the engine will be started, and its operating time can be configured.

Automatic restart will occur at specified intervals. To install them, you need to press the car lock or unlock button no later than 5 seconds after autostart is activated, if you need to start the engine every hour. The button with the key symbol sets the interval to 2 hours. The additional channel key sets an interval of 4 hours, and the silent mode allows you to start the engine every 12 hours.

It is also possible to configure autostart based on temperature. To do this, you need to connect a separately purchased sensor in parallel with the hood limit switch. Temperature-based autostart is activated by pressing and holding the buttons with the key and trunk icons.

How to remove hourly autorun

When you need to transfer the ignition control from the MHz 434 car alarm to the key, you need to remove the hourly autostart of the engine. To do this, you will need to simultaneously press and hold the security control buttons and with the key symbol. The key fob speaker and siren will give a confirmation signal. The clock icon indicating autorun mode will disappear from the communicator display. After this, you can start and stop the engine with the ignition key.

Step-by-step instructions for setting the time on the Tomahawk alarm key fob

The Tomahawk key fob is a car alarm that has a dialog code and operates at a frequency of 868 MHz. In city conditions, the communication range increases. The more buildings there are between the car and the key fob, the worse the connection between them.

The control mode provides a communication range of no more than 600 m, and in the alert mode to the key fob - 1300 m. The kit includes two key fobs and an instruction manual. In addition to the main characteristics, it describes in detail how to set the time on the Tomahawk keychain.

Why might you need a clock on an alarm key fob?

The main key fob has five buttons and an LCD monitor. On the additional one there are four buttons, as well as an indicator diode.

For devices to operate correctly, permission to use the frequency range is not required. Data encryption occurs using FM modulation. This makes it easy for code grabbers to intercept the signal.

Using the key fob, you can turn the alarm on or off, as well as control the closing or opening of the door when the key is in the ignition.

If you make the necessary settings, you can use the key fob to start or stop the engine, open or close the trunk lid.

A very convenient function is to search for your car in the parking lot. Depending on the Tomahawk keychain model, its functionality may vary slightly.

On the display of the main key fob, there are a number of indicators with specific functionality. Regardless of the Tomahawk model, there are standard indicators.

The main ones:

  • parking brake condition,
  • security mode,
  • on off. sirens,
  • block/unblock central locks,
  • alarm,
  • timer,
  • the trunk lid is open or closed,
  • car key fob recognition zone indicator,
  • anti-robbery mode.

How to set the time on a Tomahawk key fob?

Basically, only key fobs that have a two-way communication channel can be configured. There is no ability to adjust the volume on it.

For the timer and time sensor to work correctly, you must first perform some manipulations, namely:

  • Hold the KH05 button for a few seconds until the Settings message appears,
  • switch time forward and backward using buttons KN03 and KN04,
  • If the KH05 button is pressed once, it switches to setting the minutes.

Once the time is set correctly, according to the desired time zone, you can proceed to setting the alarm. Everything happens exactly the same, only the KH05 button must be pressed twice in a row.

The display of the main key fob is backlit, which greatly simplifies its use at night.

The Tomahawk system has one very useful function, namely starting the engine by time or by an engine temperature monitoring system.

In the first case, this is very convenient in that early in the morning before going to work, you do not need to sit in the car and wait for it to warm up.

Its functionality lies only in the fact that the owner of the vehicle only sets a timer and at this time the car starts and waits for its owner.

In the case where the system needs to monitor the engine temperature, it is a little more complicated, but this function is extremely important. As soon as the engine temperature drops below normal, the system detects this and forcibly and independently starts it.

Another additional option is the Turbo Timer. It is suitable for cars with a turbocharged engine. After the car owner removes the key from the ignition, the engine continues to run for about 6 seconds. Then it turns off automatically.

Fragment of the operating instructions

The alarm connection diagram is quite simple.

You can download the alarm operating instructions here: https://alarmspec.ru/wp-content/uploads/2017/10/tomahawk-tw-9100.pdf

After proper installation, you can start using the device. First, you should check the functionality of the system and the correctness of its connection.

To do this, you just need to hold down the red panic button and see if the system responds.

The instruction manual contains the appropriate information regarding this model of security system:

  • main functions;
  • detailed installation instructions;
  • connection diagrams;
  • basic settings.

Summing up, we can draw some conclusions. The Tomahawk car alarm has wide functionality and practicality.

In addition to security functions, it is also an excellent assistant in “communicating” with your car. If at first glance it might seem that the time on the key fob is needed simply to always know what time it is, then after studying the instructions from the manufacturer in detail, the consumer will understand the importance of this function.

The most effective ways to start an engine using Tomahawk

  • 1 The most effective ways to start an engine using a Tomahawk
  • 2 Step-by-step instructions with explanation will help you set the time on the key fob

ATTENTION! A completely simple way to reduce fuel consumption has been found! Don't believe me? An auto mechanic with 15 years of experience also didn’t believe it until he tried it. And now he saves 35,000 rubles a year on gasoline! Read more"

Now there are several most popular ways to start the engine when using such a Tomahawk alarm:

  • Starting with temperature monitoring, when the system independently monitors the condition of the engine and starts it automatically when necessary.
  • Starting a car alarm using an alarm clock. When the time for periodic engine starting is set on the key fob.

Each car owner independently chooses the method he will use. Proper equipment setup is the key to success.

Starting a car engine on time is the most popular and very fast way. But in order to do this correctly, you must first configure the key fob.

To cope with this task, you need to read the instructions yourself, which will help you quickly set up the key fob for proper operation.

Setting the clock is very simple and straightforward, but not everyone knows how to set the time correctly. Below are instructions to help you set up your Tomahawk key fob.

Tomahawk X5

Setting the time value on the X5 alarm does not require additional knowledge; it is simple and straightforward.

  1. Press and hold the “Speaker Crossed” key for five seconds until the second beep sounds.
  2. The dial on the display blinked.
  3. Use the “Open the car” and “Trunk” buttons to set the clock readings.
  4. To skip to minutes, press once again “Crossed out radio speaker”.
  5. Change the values ​​using the same keys.
  6. Don't touch anything for a few seconds. The electric clock of the X5 pager has been adjusted.

Remote engine start

To remotely start the engine, you need to press button No. 4 (key) - the car will respond with a triple flash of parking lights and three siren signals. One of the messages will appear on the display:

  • 5t – an attempt was made to start the engine;
  • 5P – attempt to start the engine failed;
  • image of a car with clouds of exhaust gases - the engine is running.

The car engine will run for a pre-programmed time (5/10/15/20 minutes) and then turn off. To extend the operating time, you need to simultaneously press buttons No. 4 (key) and No. 5 (lock). Each subsequent press of these buttons increases the engine warm-up time by 5 minutes. The key fob display will show the value of the programmed engine operating time.

How to install

The installation instructions contain standard recommendations for placing components:

  1. The electronic unit is located in the instrument panel (at a short distance from the lock installation site). The installation point should not be filled with liquids or heated by air flows from the air conditioning unit.
  2. The antenna is mounted on the upper edge of the glass (to increase the range of the remote control).
  3. The siren is located on the bulkhead separating the engine compartment from the passenger compartment. It is recommended to point the socket downwards (to drain condensate).
  4. Place additional limit switches; installation areas should not be flooded with water. The impact detection sensor is installed in the passenger compartment, the part is screwed to the metal elements of the body. The control diode is placed on the panel or racks (on the TZ version the unit is located in the antenna block), the tuning key is located in a hidden cavity.
  5. After installation, you need to install power cords and program the operating parameters of the alarm.

In order to turn on the security mode, you must press the button...

Page 9

  • Image
  • Text

To turn on the security mode, you must press the button. Parking

The lights will flash 1 time, the siren will emit 1 “CHIRP”, confirming entry into the security mode, doors

and the windows will close (if connected).

LCD display:

Attention!

If, when arming, the siren emits 4 “CHIRPS” and parking

The lights will flash 4 times, which means that the system has detected and disabled a faulty security zone (the door, hood, trunk are open, the parking brake is not applied). On LCD

key fob pager will display a faulty security zone. The system automatically

will take it under guard as soon as it is fixed (door, hood, trunk will be

closed, parking brake applied).

6. Arming

7. Arming with siren turned off

To turn on the security mode with disabling siren sound alerts

(all messages and confirmations are sent by the system only to key fobs-pagers) you must press the button once. The parking lights will flash 1 time to confirm

entering security mode, doors and windows will close (if connected).

LCD display:

Note.

You can also turn this mode on and off while the vehicle is in

security mode by pressing the button.

8. Arming with the engine running

This TOMAHAWK model provides the ability to protect a vehicle with a running

engine. To enable this mode you must:

1. Start the engine. 2. Get out of the car, close the doors, hood, trunk.

3. Press the button, the door locks will close. 4. Within 3 seconds. after completing step No. 3, press the button again, siren

will emit 1 “CHIRP” and the parking lights will flash 1 time.

9

How to reset Tomahawk TW 9010 alarm settings

You can go to factory settings like this.

  1. Turn on the ignition system.
  2. Press the service key ten times.
  3. Turn off the ignition. The siren will sound 10 times.
  4. On the remote control, press the button with the image of a key.
  5. Turn on the ignition. The lights will blink five times.

After completing all the steps, you need to reprogram the Tomahawk 9010 functions:

  • autostart by time;
  • by temperature;
  • turning on the turbo timer;
  • window closing time;
  • automatic door closing, etc.

How to control the turbo timer

By default, the turbo timer is turned off; to activate it, you need to turn it on and program the required operating time. This is done simply:

  • The car must be put on the handbrake (with the engine running) - the car alarm will start counting down the time.
  • Remove the key from the ignition.
  • Enable the “Security” function (if required).

Tomahawk systems are designed so that the time will begin counting immediately after the handbrake is applied to the PARK mark. For cars with a Start/Stop button, everything looks a little different:

  • The handbrake must be applied (the engine must run for at least 1 minute).
  • Leave the car.
  • Close the doors.
  • Enable the "Security" function.

The engine will stop after the last action is completed. The turbo timer not only increases the life of the turbine, but also the battery; it will not be discharged due to the frequency of starting and stopping the engine.

How to setup

Before you start using the Tomahawk alarm, you need to set the operating parameters. Alarm settings are made using the Override button; to activate the setting mode, you need to press the button 5-6 times (depending on the type of adjustment). Then the owner selects the required function value, based on the tables available in the documentation. The parameter is assigned using buttons, the choice is confirmed by the corresponding number of beeps and a siren.

To reset the parameters, you need to activate the procedure by pressing the Override button 9 or 10 times (depending on the table number), and then turn on the ignition. The complex will sound 9 or 10 beeps, respectively; after briefly pressing the button on the remote control, marked with a padlock with a locked shackle, the settings are deleted. The driver then programs the parameters again.

Neutral setting algorithm:

  1. After stopping the machine, tighten the parking brake lever. The box is first moved to the neutral position, the power unit is not turned off.
  2. Hold the button marked as an open lock until the buzzer or green control diode (on the auxiliary remote control) turns on.
  3. Press the button again (the interval between impacts does not exceed 3 seconds). If the procedure is carried out correctly, a melodic signal will turn on (on the remote control with a display).
  4. Remove the key from the lock. On cars with a button to start and stop the engine, the step is not used.
  5. Unlock the door, get out of the car, and then slam the door. The security system will automatically stop the engine and lock the locks.

Tomahawk 9.7 car alarms allow programming of an automatic algorithm. After activating the handbrake, you need to remove the key and then leave the car. After pressing the remote control button, the protection is turned on and the power unit is stopped at the same time.

The Tomahawk alarm system supports automatic engine start without using a key. The complex's central processor turns on the starter based on a timer signal or data received from a temperature sensor. The complex disables the protection of the power unit circuits, and the shock sensor is temporarily deactivated. The starter rotates the motor shaft; after the engine starts running, the starter is automatically turned off (based on signals from the generator or speed sensor). After warming up within a specified time, the engine stops and is armed.

The start is carried out according to signals from sensors installed in the cabin (inside the antenna unit) or in the engine compartment. The factory sets the default start from the cabin sensor (for example, in 9.7 complexes). To activate the sensor in the engine compartment, you will need to modify the wiring harnesses and program the central unit. The adjustment algorithm and wiring diagram are given in the manual.

  1. Press the button on the alarm remote control, marked with a locked padlock symbol. The key is held until the buzzer sounds or the control diode blinks. Then you need to briefly press the key with the lock icon with the shackle open.
  2. After sound and light signals are given, the icon with the text “1-2 Temp Start” will turn on on the remote control, and the threshold temperature value will also be displayed (programmed when setting up the unit).
  3. When the engine starts, the key fob emits a 5-fold signal, and an icon in the form of an exhaust cloud is displayed on the display, indicating that the engine is running. The number of restarts is not limited, the warm-up time between starts is at least 2 hours (the parameter is not forcibly regulated). The car owner adjusts the warm-up time.

Trigger by time

The car owner can turn on the hourly engine start by successively pressing buttons with the symbols of an open and locked lock. The text message 2-1 Daily will appear on the screen and the power unit will start. After warming up (the time is programmed when setting up the central unit), the engine will stop. Further starts are performed after 1, 2, 4 or 24 hours (the parameter can be configured separately).

Installing a Tomahawk 9010 turbo timer

To activate or disable the Tomahawk turbo timer, you need to enter programming mode. To do this, find the “Override” service button in advance, which is usually located in the dashboard or under it.

Further steps for setting up the TW 9010 turbo timer are as follows:

  • with the engine not running, turn on the ignition;
  • press the service key 6 times;
  • turn off the ignition.

The siren will emit 6 short beeps, which means you have entered programming mode. Now you need to select the turbo timer setting by pressing the “Override” service key 16 times. If you did everything correctly, the siren will emit 3 long signals and one short one. Now select a function using one of the 4 buttons on the Tomahawk key fob:

  • 1 – disabling the turbo timer;
  • 2 – one minute of engine operation;
  • 3 – three minutes;
  • 4 – six minutes. idle move.

The selected option is confirmed by the corresponding number of short siren beeps, after which the alarm exits the programming menu. When activated, the engine will always run for the specified number of minutes after you remove the keys from the ignition. To do this, you need to put the car on the handbrake (for a manual transmission) or neutral (for an automatic transmission).

Functions

Tomahawk 9030 security systems support the following functions:

  • built-in protection against signal interception;
  • double blocking of the power unit;
  • additional immobilizer;
  • emergency disabling of security using a digital code;
  • automatic activation of security;
  • giving alarm signals by siren or external lighting equipment;
  • protection of a car with a running engine;
  • remote engine start;
  • support for automatic start of the power unit;
  • built-in diagnostic unit with bypass of faulty zones.

Advantages and disadvantages

Advantages of car alarms series 9030:

  • low cost of equipment;
  • additional functions are provided (automatic start or security with the motor running);
  • simple installation and configuration diagram.

Disadvantages of the complex noted by the owners:

  • cases of incorrect operation of autostart and remote controls;
  • frequent breakdowns of electronic components due to low quality components;
  • difficulties with purchasing original spare parts.

Basic functions of the turbo timer

The Tomahawk 9010 budget alarms are very popular, installed on cars with turbocharged and diesel engines. On the first, you can program the operating time for 1, 3 or 6 minutes.

For the latter, a function is provided to heat the glow plugs before the starter is turned on. Tomahawk 9030 alarm systems have an automatic hourly engine start function.

It allows you to run it at a programmed interval of 1, 2, 4 or 24 hours. In addition, this alarm makes it possible, using a turbo timer, to automatically warm up the engine according to the readings of the temperature sensor.

The car owner himself sets the required temperature. It must be remembered that automatic engine warming cannot be performed more than once every 2 hours.

Key Features

Tomahawk TW-9030 is equipped with many modern options:

  • anti-grabber, with the help of which commands sent to the control unit each time have a new unique digital code;
  • the anti-scanner does not allow code grabbers to read transmitted signals;
  • automatic remote engine start function according to specified scenarios (by time or temperature);
  • Additional triggers can be installed on all opening body elements;
  • The immobilizer will not allow an attacker to quickly start the car;
  • if you need to leave the car for a short time, you can turn on the security with the engine running;
  • The sensitivity of the shock sensor is adjustable over a wide range;
  • programmable duration of central locking control;
  • temperature sensor to inform the owner about the temperature in the cabin and activate autostart;
  • the ability to connect the “comfort” system, which allows you to automatically close the windows and sunroof when arming;
  • the standard horn can be used as a siren;
  • Panic mode, which can be used to attract the attention of others;
  • “Valet” mode to provide access only to service functions when transferred to third parties;
  • “Anti-Hijack” mode, used to gradually block the engine at a distance, this is used when trying to steal a car;
  • “silent” security mode, in which the car does not give any external signals, but all information is sent to the key fob;
  • ability to program 4 key fobs, storing information about linked key fobs in memory;
  • function of automatic closing of doors after starting to move;
  • the ability to remotely start the car using the key fob;
  • the ability to configure autostart on diesel and gasoline cars, with manual and automatic gearboxes;
  • a turbo timer that ensures that the engine operates after the ignition is turned off to cool the turbine.

Functions of the main key fob:

  • all linked key fobs display the current system status;
  • vibration alert about activation;
  • equipped with screen backlight;
  • built-in clock, which the system is guided by when autorun is running;
  • timer, alarm clock;
  • switching to power saving mode;
  • a lock that protects against accidental pressing of buttons.

Problems with autostart Tomahawk

Since the autostart algorithms for alarm systems of this brand have changed little since the time of the Tomahawk TW-9010 (minor differences are due primarily to the introduction of support for Start-Stop systems), the information regarding this system can be applied to newer ones. On cars with a manual transmission, like other alarm systems with auto start, it will require the correct completion of the “software neutral” procedure. Moreover, here this procedure is set rigidly by the manufacturer and is not customizable by the user.

The soft neutral procedure includes:

  1. Pull the handbrake with the engine running.
  2. Press the autostart button on the key fob - after that, an indication of engine operation (a cloud near the exhaust pipe) will appear on its screen.
  3. Remove the key from the ignition - if everything works correctly, the engine will not stall.
  4. Get out of the car. When the door is closed, the engine will stop.

How to turn off the alarm

Standard alarm disabling

To disable the security mode, you need to press button No. 4 “Key” on the remote control. The doors will then unlock, the lights will flash twice, and the alarm will emit two short trills. The optional courtesy interior lighting will turn on.

IMPORTANT: If, when you try to disable the security mode, the alarm makes three short trills, and the key fob makes one long beep, it means that some kind of sensor has been triggered.

Disabling the alarm in emergency mode

If the alarm is in alarm mode (a siren sounds, the lights flash), then to disable the security mode you need to take the remote control key fob and press button No. 4 “Key” twice: the first press will disable the alarm mode, the second - the security mode.

Activation from the X5 alarm key fob

To activate the turbo timer on the Tomahawk X5, you need to enter the programmable functions menu. To do this, you should find the “Override” button located in the cabin. Further sequence of actions:

  • in unprotected mode and with the car turned off, turn on the ignition;
  • press the service key “Override” 6 times;
  • take out the key.

The alarm will emit 6 short sounds, which confirms the correctness of the actions performed. Then we set up the Tomahawk turbo timer - again press “Override” 1 time, after which we will hear 1 short signal. By activating one of the pager keys, we select the time for automatic operation of the motor:

  • 1 – one minute;
  • 2 – two;
  • 3 – three;
  • 4 – six minutes.

After activating the desired mode, the alarm will confirm with the appropriate number of sounds. Now the turbo timer will work after setting the car to the parking brake (neutral) and security.

Rating
( 2 ratings, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]