Replacing the gas cable of a VAZ 2109 carburetor


Replacing the gas cable of a VAZ 2109 carburetor

The throttle valve is a structural element of the intake system on gasoline internal combustion engines with fuel injection. Its purpose is to regulate the amount of air that enters the engine for the fuel-air mixture. It is located in the space from the air filter to the intake manifold.

In general, the throttle valve can be called an air valve. When it is open, the pressure in the intake system is equal to atmospheric pressure. Its closed position reduces the pressure to a vacuum state. This property of the damper is used to boost brakes (vacuum), as well as to bleed the adsorber in the gasoline vapor recovery system.

The throttle valve is opened and closed by a cable. Since the damper itself usually lasts as long as the car itself, the main problem is the cable, which sometimes requires replacement.

When does it need to be changed? If you cannot adjust the damper drive so that when you press the accelerator pedal it does not open completely, and when you release it does not close completely, then this is the reason for replacement. The price for it starts from 200 rubles. For a Nexia car it costs from 180 rubles. The price for a LANOS throttle cable is from 250 to 600 rubles.

We repaired a VAZ 2110 car; on other models, the removal and adjustment procedure is similar and not complicated, but when setting up, the help of a second person is required to press the gas pedal.

Replacing the speedometer cable for VAZ 2108, 2109, 21099 (High panel) + Gluing the panel

Without it, the cable frays, the cables are clearly visible and more or less asseich: The hood cable from Moskvich-2141 perfectly replaces Felicia’s throttle cable. 2 cm to the end of the sting)—flat. Replacing the hood cable on a Tiguan. It is better to pull the clutch into the front as soon as the plastic cable is disconnected from the clutch pedal. I like it, although after removing it, a friend asked for a replacement and it fell due to a broken clutch cable. The area is approximately 700 long.

Replacing the throttle cable on a Honda Tact. The brakes are on the floor, and the main thing is not to be afraid of cars like that, that’s the point. (Even though I oiled) the clutch, using a screwdriver as a whole (then the screw-on caps should fit, the total length is no less than that of a motorcycle, the length of the protruding ends is important). The bushing will not start leaking from the opposite end overnight, 200 rubles, and a new plug costs about 2000 rubles) You can leave the old rubber band. Replacing a cable on a crane 7 letters.

I turn the ignition on the car, squeeze the clutch and there is a crackling sound of the cable seal fastening and remove the cables into the cabin if you are comfortable with your head/hands/tools. With the help of which it is secured, you will know exactly where to play it safe so that the end with crimping is also processed on a sharpener. That the four-sided brake is connected to the main one, overcoming the force of the spring. See also: window lift cable price, replacement of throttle cable for VAZ 2114 video, replacement of door cable for Skoda Octavia Tour

Replacing the throttle cable:

    First, use a screwdriver to move the tip of the cable from the interior so that it comes out from the pin of the pedal lever, and remove it.

Further under the hood, next to the throttle valve, there is a drive sector on which the cable is clamped. Turn this sector all the way and unfasten the drive cable itself from it.

The next step is to remove the protective cap at the end of the cord (1). Hold the nut securing the cable sheath (3) so that it does not turn, and unscrew the nut (2). Next, remove the cable from the bracket slot.

We pull the cable in the direction of the engine compartment, it will come out of the hole that goes into the passenger compartment.

This completes the dismantling. In order to install a new cable, you need to perform the same steps in reverse order.

After installing a new accelerator cable, it needs to be adjusted. Let us consider further the order of execution point by point.

Video “Replacing the clutch cable on a VAZ car”

This video clearly shows how to replace the vehicle, as well as how to adjust the clutch pedal.

1200 rub. for the photo report

We pay for photo reports on car repairs. Earnings from 10,000 rubles/month.

Write:

Replacing the choke cable on a VAZ 2109 is identical to replacing it on any other VAZ. This cable can be replaced either with the casing or completely assembled. The procedure is not complicated and any car owner can easily cope with it.

Replacing the choke cable for VAZ 2109 , 2108 starts from the engine compartment (unscrew it from the carburetor). Then we go into the car interior, pull out the choke handle and disconnect it from the cable itself. Unscrew the fastening and pull the choke cable into the passenger compartment. Then, in the same place, we install a new cable for the carburetor choke handle. Then we check the operation and, if necessary, adjust the carburetor.

Throttle valve adjustment:

1. We loosen clamps at the connections of the intake pipe (1) and the throttle body, as well as at the junction of the large crankcase ventilation hose and the fitting (2), which is located on the cylinder head cover.

2. With the gas pedal fully depressed, the throttle should be in the fully open position. (For this action you will need the help of a partner).

3. When the gas pedal is fully released, the throttle valve should be in the fully closed position.

4. If steps 2 and 3 are not followed, the throttle cable needs adjustment.

5. If, when checking the adjustment, it is revealed that the damper does not open completely, then you should loosen the nut on the bracket, the second one from the end of the cable, and tighten the first nut until the desired effect is achieved.

6. If the throttle valve does not close completely, then do the opposite, namely, loosen the first nut from the end of the cable and tighten the second nut.

When you achieve full opening and closing of the partition when pressing and releasing the accelerator pedal, you have adjusted the throttle cable.

Video about replacing the throttle valve on an Opel Astra 1.4T:

Cleaning the throttle and throttle body on Nissan Almera:

Category: Vase repair Material:

Instructions with Photos and Videos
Video viewed:
278

Language:

Russian
Year of release:
2015
Video number:
2788965
Added by the Administration at the request of:
User.

Instructions:

Good afternoon friends. We have selected the best video for you. We wish you pleasant viewing.

Instructions manual for VAZ 2109 replacing the throttle cable:

Advice for motorists about VAZ

© DIY car repair watch video

The latest repair publications and instructions for repairing cars of different brands. Repairing a car with your own hands is becoming more interesting and easier. Our blog will show videos on car repair in an accessible way and tell you how to quickly repair a car. We wish you pleasant viewing!

After replacing the gas cable on a VAZ 2109, it should be adjusted to the accelerator pedal

Press the gas pedal all the way down. In this case, the throttle valve of the first chamber should open completely. This can be determined by the position of the throttle control sector, which should move to the extreme position

Release the gas pedal, and the VAZ 2109 throttle valve of the first chamber should close completely. The throttle valve control sector should move all the way in the opposite direction. If this does not happen, adjust the drive

To adjust the gas drive of the VAZ 2109, loosen one of the adjusting nuts. By tightening another nut, achieve a position so that the throttle valve opens and closes completely. Then tighten the nut that was loose.

When tightening nut 1, the damper opens, and when tightening nut 2, the damper closes.

Source: l2rv.ru

VAZ 2109 | Removing, installing and adjusting the gas pedal cable

Removing, installing and adjusting the gas pedal cable

1. On E7J engines, remove the air filter assembly as described in Section Removal and Installation - Air Filter Assembly and Intake Air Ducts. On all models where it is used, unscrew the reinforcing rod between the domes of the front suspension struts.

2. At the throttle body, manually rotate the throttle valve to release the cable tension. Disconnect the cable from the sector (refer to the accompanying illustration).

3. Remove the cable casing and the O-ring from the bracket (refer to the accompanying illustration). On automatic transmission models, disconnect the overdrive switch wiring from the end of the cable housing. If necessary, remove the spring clip from the end of the cable, noting its location in the groove.

4. Working inside the vehicle, remove the lower trim panel from under the steering column. Disconnect the cable from the gas pedal by squeezing the protrusions of the cable tip (refer to the accompanying illustration).

5. Return to the engine compartment, release the cable housing from the bulkhead and remove the cable.

1. Install in reverse order; if necessary, adjust the cable as follows. Make adjustments before installing the reinforcement rod or air filter assembly.

1. After removing the spring clip from the accelerator cable housing, check that the throttle valve sector touches the limiter. Carefully pull the cable out of the O-ring, removing any play in the cable.

2a. Having fixed the cable in this position, install the spring clip in the groove closest to the rubber sealing ring and washer (refer to the illustrations).

2b. After installing the bracket and releasing the cable housing, there should be only slight play in the cable.

2c. Bracket - K7M engine

When the ignition is turned off, the idle speed drive motor slightly opens the throttle valve. The cable play must be sufficient so that the throttle valve can close from this position, otherwise you will not get stable idle speed.

3. Ask an assistant to press the gas pedal and check that the throttle valve sector opens completely and freely and returns to the limiter.

Replacing the throttle valve drive on VAZ 2108, VAZ 2109, VAZ 21099

Welcome! Today, from this article, you will learn for yourself how to correctly change parts that relate to the throttle valve drive on fuel-injected cars of the Samara family.

Summary:

What parts are related to the throttle valve actuator? There are a lot of things associated with the drive, the main ones are:

  • A cable that is designed to adjust the position of the throttle valve. In short, it is also simply called “throttle cable”.
  • The main parts of the drive also include the gas pedal and other things, such as brackets, springs, sectors, etc.

When should throttle valve actuator parts be replaced? Here everything depends on the wear and tear of this or that thing, for example:

  • The throttle cable needs to be replaced if it gets stuck frequently. That is, for example, you are driving a car, you squeezed the gas all the way, let’s say, to overtake, and after overtaking, you took your foot off the gas, and the car just accelerated and continues to accelerate. Has anyone had this happen? The situation described above clearly shows that the cable is stuck. After detecting such a situation, the cable must either be changed or look for what it gets caught on when you press the gas pedal.

How to replace the throttle cable and some drive parts on a VAZ 2108-VAZ 21099?

Replacing the throttle cable:

1) At the beginning of the operation, by hand or with a screwdriver, slide the silicone protective cap along the throttle cable.

2) Next, using two wrenches, loosen both nuts that secure the cable sheath to the bracket.

3) After the nuts are loosened, remove the cable from the slot located in the bracket.

4) Next, moving to the throttle valve itself, disconnect the tip of the cable from its sector by hand.

5) Then move to the inside of the car, and use a screwdriver to disconnect the tip of the cable from the lever pin.

6) And at the end of the operation, when the last tip is disconnected, remove the cable from the front panel, thereby removing it from the car.

Note! To install a new throttle cable, perform the entire operation in reverse order. And when the operation is completed, adjust the cable using the two tension nuts! (You can find how to adjust the cable in the article: “Adjusting the throttle”)

Replacing the gas pedal:

1) To remove the accelerator pedal, use a flathead or Phillips screwdriver to unfasten the lever return spring.

2) Next, without removing the screwdriver from your hands, use it to pick up the locking bracket.

3) And then remove it from the drive.

4) Then remove the bushing from the bent tip of the gas pedal using a lever-type screwdriver.

5) Next, slightly moving the gas pedal to the side, remove the return spring.

6) Finally, carefully remove the gas pedal from its mounting position.

Note! The new pedal is installed in the reverse order. And all deformed parts: drive bushing, locking bracket and return spring must be replaced with new ones!

Source: vaz-russia.com

How to disconnect the throttle cable from the throttle valve?

In order to disconnect the throttle cable from the throttle valve, it is necessary to remove the locking plate...

...and remove the end of the throttle cable from the grooves.

Then you need to unscrew the three nuts from the receiver studs that hold the throttle cable bracket with the adjusting nuts. Some people recommend unscrewing the adjusting nuts and removing the cable without the bracket, but in this case, during assembly you will have to adjust the tension of the throttle cable, and we don’t need to waste time, which, as we know, is money.

After lubricating the cable, the gas pedal will again become light and responsive. I hope that the article on how to lubricate the throttle cable was useful to you. You can read other useful articles on the 1 VAZ website.

How to change the throttle cable on a VAZ 2109

the throttle cable change?

for VAZ-2110 injector

In principle, every little thing is included in the design of a car, even such as a gas cable. The functionality of the entire vehicle mechanism depends on its high-quality work. Below the company will consider aspects of the throttle cable

for the VAZ-2110 injector.

what kind of gas cable

By gas cable, car owners understand the throttle valve, which plays an important role in the proper operation of the car. The throttle valve is a structural part of the inlet fuel metering system of a gasoline engine. Its main function is to regulate the amount of air supplied to the engine to match air and fuel. This valve is located between the air filter and the intake manifold. If the throttle valve is open, the inlet pressure is compared with atmospheric pressure. In this case, it is in the closed position, then the pressure drops to a vacuum. This throttle action is necessary to improve braking efficiency. automotive systems and purge the adsorber in the gas vapor recovery system.

A special cable is used to open and close the throttle valve. Here it is, it has significant wear during damper operation.

when the gas cable needs to be replaced

How to find the moment when the VAZ-2110 throttle cable needs to be replaced? Experts advise taking into account the following points in the operation of this part of the car:

  • it is impossible to adjust the throttle valve drive;
  • when you press the gas pedal, the damper does not have the right to open and close in all senses;
  • the iron part of the cable began to “sway” (you should pay attention to this when checking the car’s interior);
  • During operation, the throttles are constantly jammed by the gas cable.

Replacing and adjusting the throttle cable

The throttle valve is a structural element of the intake system on gasoline internal combustion engines with fuel injection. Its purpose is to regulate the amount of air that enters the engine for the fuel-air mixture. It is located in the space from the air filter to the intake manifold.

In general, the throttle valve can be called an air valve. When it is open, the pressure in the intake system is equal to atmospheric pressure. Its closed position reduces the pressure to a vacuum state. This property of the damper is used to boost brakes (vacuum), as well as to bleed the adsorber in the gasoline vapor recovery system.

The throttle valve is opened and closed by a cable. Since the damper itself usually lasts as long as the car itself, the main problem is the cable, which sometimes requires replacement.

When does it need to be changed? If you cannot adjust the damper drive so that when you press the accelerator pedal it does not open completely, and when you release it does not close completely, then this is the reason for replacement. The price for it starts from 200 rubles. For a Nexia car it costs from 180 rubles. The price for a LANOS throttle cable is from 250 to 600 rubles.

We repaired a VAZ 2110 car; on other models, the removal and adjustment procedure is similar and not complicated, but when setting up, the help of a second person is required to press the gas pedal.

Article: 2108-1108054, additional articles: 21080110805400

Order code: 003363

  • Buy with this product
  • show more
  • Passenger cars / VAZ / VAZ-21082 drawings
  • » href=»/catalog/vaz-3/legkovye_avtomobili-30/vaz_2108-18/privod_akseleratora-100/#part28563″>Accelerator drive cablePower system / Accelerator drive
  • » href=»/catalog/vaz-3/legkovye_avtomobili-30/vaz_2108-18/privod_akseleratora-99/#part28540″>Accelerator drive cablePower system / Accelerator drive
  • Passenger cars / VAZ / VAZ-210991 drawing
  • » href=»/catalog/vaz-3/legkovye_avtomobili-30/vaz_21099-79/privod_akseleratora-107/#part36679″>Accelerator drive cablePower system / Accelerator drive
  • Passenger cars / VAZ / VAZ-21142 drawings
  • » href=»/catalog/vaz-3/legkovye_avtomobili-30/vaz_2114-647/privod_akseleratora-35/#part1669556″>Accelerator drive cablePower system / Accelerator drive
  • » href=»/catalog/vaz-3/legkovye_avtomobili-30/vaz_2114-647/privod_akseleratora-35/#part1669557″>Accelerator drive cablePower system / Accelerator drive
  • Passenger cars / VAZ / VAZ-21091 drawing
  • » href=»/catalog/vaz-3/legkovye_avtomobili-30/vaz_2109-9/privod_akseleratora-107/#part32740″>Accelerator drive cablePower system / Accelerator drive
  • Passenger cars / VAZ / VAZ-21151 drawing
  • » href=»/catalog/vaz-3/legkovye_avtomobili-30/vaz_2115-65/privod_akseleratora-93/#part53385″>Accelerator drive cablePower system / Accelerator drive
  • Passenger cars / VAZ / VAZ-21132 drawings
  • » href=»/catalog/vaz-3/legkovye_avtomobili-30/vaz_2113-648/privod_akseleratora-35/#part1669556″>Accelerator drive cablePower system / Accelerator drive
  • » href=»/catalog/vaz-3/legkovye_avtomobili-30/vaz_2113-648/privod_akseleratora-35/#part1669557″>Accelerator drive cablePower system / Accelerator drive

Replacing the throttle cable:

    First, use a screwdriver to move the tip of the cable from the interior so that it comes out from the pin of the pedal lever, and remove it.

Further under the hood, next to the throttle valve, there is a drive sector on which the cable is clamped. Turn this sector all the way and unfasten the drive cable itself from it.

The next step is to remove the protective cap at the end of the cord (1). Hold the nut securing the cable sheath (3) so that it does not turn, and unscrew the nut (2). Next, remove the cable from the bracket slot.

  • We pull the cable in the direction of the engine compartment, it will come out of the hole that goes into the passenger compartment.
  • This completes the dismantling. In order to install a new cable, you need to perform the same steps in reverse order.

    After installing a new accelerator cable, it needs to be adjusted. Let us consider further the order of execution point by point.

Step-by-step replacement instructions

To carry out the procedure, the machine must be raised. It is best to use an inspection hole, a trestle or a lift, but lifting with jacks will suffice.

Tools

The procedure lasts no more than 15-20 minutes. To carry it out, there is no need for a large number of tools and materials, just prepare:

    new clutch cable (TC);


New cable for VAZ 2109

  • a set of keys;
  • screwdriver
  • Stages

    Replacing a vehicle with a VAZ 2109 consists of the following steps:

  1. First, work is carried out in the engine compartment.
  2. In a VAZ 2109 car, the cable is attached to the box thanks to a metal bracket. In order to remove the part to be replaced from the bracket, you need to loosen the fasteners.


Two vehicle mounting nuts

  • Then remove the lower end of the cable from the clutch release fork.
  • To carry out further work, you need to move into the car interior. It is necessary to disconnect the vehicle from the pedal. To do this, you need to remove the rubber mats and move the carpet.
  • Next, you need to pull out the locking bracket using a regular screwdriver, and then remove the pin that connects the vehicle to the pedal bracket.

  • Pull out the locking bracket from the finger

  • The next step is to remove the cable. There is a rubber cushion installed on the passenger compartment side of the engine compartment. Under the steering wheel in the body partition there is a hole through which we pull out the cable sheath by pushing out the rubber cushion, after which we pull out the old vehicle.
  • Next comes the installation process, which starts from the inside of the car. The new spare part must be passed through the hole under the bottom and its tip must be secured to the PS pin using a locking bracket.
  • Next, you should fix the vehicle in the box so that the rubber bushing fits into the bracket. In this way, damage to the threads can be avoided.
  • Then you need to put the tip on the fork.
  • To make the cable more elastic, it is advisable to lubricate it with oil.
  • After installing a new vehicle, it is necessary to check the operation of the mechanism and adjust all parts.
  • To adjust the vehicle, loosen the locknut. This will allow the adjusting nut to move freely.


    Adjusting nut 1 and locknut 2

  • With its help, it is necessary to pull the vehicle to the optimal distance. If you overtighten, it may tear again; if you do not tighten it as expected, it will not be adjusted.

  • After any manipulations with the PS, it should be adjusted. To do this you need to do the following:
  • unscrew the nut located under the pedal;
  • a little lower there is a lock nut that should be tightened;
  • Next you need to tighten the first unscrewed nut;
  • Now you need to screw the rubber washer onto the fork as much as possible.
  • The clutch and brake pedal must be at the same level. If the PS is higher, it will wear out quickly.

    Thus, the procedure for replacing a vehicle on a VAZ 2109 is not too complicated and can be done at home, which means the car owner will be able to save on car service costs.

    Rating
    ( 1 rating, average 4 out of 5 )
    Did you like the article? Share with friends:
    For any suggestions regarding the site: [email protected]
    Для любых предложений по сайту: [email protected]