Dashboard lights blinking VAZ 2109

Common instrument panel faults

The instrument cluster on the VAZ 21099 or 2109 is a fairly reliable unit. However, even this can fail over time.

The main malfunctions characteristic of the VAZ instrument panel:

1. The lights on the instrument panel of the VAZ 2109 stopped lighting. If only a few light bulbs refuse to work, then most likely the reason lies in their burnout. If the instrument panel lighting stops working completely, then most likely the problem is a poor power supply. As practice shows, power problems are usually caused by either damaged wiring or oxidation of contacts at connections and connectors. If this is the case and the backlight does not light up due to oxidation, then you can get rid of this problem by cleaning the contacts or replacing them. If the problem lies in the lighting sources, then replacing the lamps will solve it.
2. Another problem, oxidation on the circuit board, is common in older vehicles or vehicles with moisture present. Due to oxidation of the board, the backlight and some instruments may not work, in particular, fuel level and coolant temperature controllers, tachometer, etc. If the needles do not rise on the tachometer, speedometer, fuel consumption sensor and generator voltage, or they work chaotically, then you need to carry out a full check of the dashboard.
3. VAZ 2109 cars are characterized by the problem of a non-working speedometer. As a rule, it appears as a result of wear of the cable connected to the box, or due to repairs to the device and its incorrect connection. If the cable is worn out, then you just need to replace it, there is nothing complicated about it. The main thing is to connect the cable correctly so that its tip fits exactly into the groove on the tidy speedometer.
4. Damage to the board itself. Such a malfunction occurs quite rarely, but, nevertheless, it should not be forgotten. If the structural board fails, the shield will have to be repaired, but if this does not help, then it will need to be replaced.

Panel tuning options

If you decide to tune your instrument panel, then most likely you will be interested in knowing what options exist for doing it. The tuning shield, as you know, pleases the driver’s eye, so this issue is relevant for many car owners.

Dismantling the shield

To tune the dashboard, you first need to remove the device itself.

To do this, you only need to disconnect eight fasteners; to do this, you can use a regular knife:

• First, the fastenings on the driver’s side are disconnected;
• then you need to release the latches located there, on top;
• after this you can disconnect the middle part of the tidy;
• the panel itself is dismantled (the author of the video is Artem Volivach).

You should not spare money on tuning the interior of the VAZ 21099

Do not spare money for a complete reupholstery of the ceiling, body pillars and doors, use high-quality leatherette. After tuning the instrument panel of the VAZ 21099, you can begin covering the gearshift and handbrake levers, as well as the rear parcel shelf and steering column.

Covers on the gas, brake and clutch pedals will come in very handy, and installing an anti-slip floor plate will add both practicality and originality to the appearance of the interior.

Tuning parts can always be found in local stores, car markets and on the Internet.

Comfortable seats with lateral support will allow you to complete the unique symphony of tuning the VAZ 21099 car. It is especially beautiful when these seats are made in a sporty style, and their design is pre-designed for installation on “nine” powerful sound speakers that will allow you to enjoy listening to high-quality music.

Reserve wheel, or patriot versus hover

2021-06-30 10:27:22

Cooling system UAZ 469 engine 417

2021-06-30 10:27:22

Tuning UAZ “loaf”: hunting palace on wheels UAZ loaf sharpen for off-road tuning

2021-06-30 10:27:22

Video “Instructions for replacing the speedometer cable on a VAZ 2109”

How to repair the speedometer on a “nine” if it stops working - visual instructions for replacing the cable at home are given in the video below (the author of the video is Vladimir Edwin).

The backlighting of the VAZ 2109 instrument panel is often not satisfactory for drivers. You can change the color and its brightness yourself, without turning to the salon for help.

To improve the lighting, you need to install LEDs instead of conventional incandescent light bulbs. Their glow is much brighter, in addition, you can choose the color of the backlight at your discretion: blue, green, red or white. These are the main colors, but if you look, you can also find purple LEDs.

Replacement of light bulbs or sockets must be carried out carefully and carefully. If the car owner decides to use LEDs to illuminate the buttons, then you need to purchase a light bulb with a regular base. Soldering and a special cartridge are needed if there is a desire to replace the backlight of the instrument cluster. Among the many LEDs, there are also those that have a diffuse or, conversely, point glow.

These effects are achieved using a focusing lens configuration. A more uniform backlight is suitable for illuminating the scale on the instrument panel, and a brighter light is suitable for the button icon. Every driver should take into account the features of design changes when improving his car.

VAZ-2109 panel: do-it-yourself modernization

The VAZ 2109 panel is made of a special energy-absorbing material. It consists of an overlay and, in fact, the panel itself. It is made of plastic. Its thickness is 3 mm. The overlay is essentially reinforced with a special metal frame. It has a reliable energy-absorbing layer made of polyurethane foam. On the outside it is lined with a special decorative film. Low and high panels of the VAZ 2109, as well as a “European panel” can be installed on the car. The high panel of the VAZ 2109, like the low one, has certain features that should be taken into account when installing them.

The installation method and the high panel are almost identical, since the mounting points, as well as the connections of the air ducts of the automobile ventilation and heating system, are the same.

The differences concern only the wiring harness connections. (The diagram of the VAZ 2109 instrument panel is shown in the photo below; follow the link to read even more about it).

How to do easy tuning of the VAZ-2109 dashboard with your own hands

During the modernization of the interior of the domestic “nine”, tuning its “tidy” becomes a truly indispensable element. Beautiful modifications can be done with your own hands. To do this, you will need to make a new dial on a computer using special design programs and printing the picture on a printer. However, first you need to clearly think through the appearance of the dials for the car tachometer and speedometer, as well as for all the sensors that remain. Once the dials are printed, they need to be laminated, and then you can begin to remove the instrument panel. To properly dismantle it, you must first remove the steering wheel pads, and also mark the steering position relative to the shaft. Then carefully unscrew the fastening nut.

Next, you can remove the steering wheel and unscrew the screws that are located in the area of ​​the car lower casing. After this, you will have to disassemble the steering column. When the instrument panel is removed, you should unscrew the arrows from the old speedometer and tachometer. Subsequently, they will be attached to the updated dials.

When tuning a VAZ 2109 with your own hands, you can also repaint the dials and hands in bright colors. Regular spray paint cans are suitable for this. At the same time, it is better to make the dial a rich black color. You can make it matte using special means. In this case, the arrows need to be painted in bright pink or original red-burgundy tones. After the painted plates of the machine dial have dried, they are equipped with an old or pre-prepared scale and removed hands. In a situation where the owner wants to modernize the instrument panel in a more modern way, he should also use a special (original, as in the video) backlight. You can add an original touch using a fluorescent marker, but more on that below.

Beautiful modifications to the VAZ 2109 panel

Every driver of a domestic car wants to make the instrument panel of his VAZ-2109 as bright and original as possible. Here is one of the options for how beautifully you can modify this element of the machine. You will need a soldering iron. Next you need to buy numbers and a scale panel. It is important that they are translucent from the inside. You should also purchase an ultraviolet lamp. It is powered by 12 volts. Therefore, nothing needs to be changed.

You will also need a fluorescent marker or paint. It will change color if exposed to ultraviolet light. This technique is often used in modern nightclubs. You will also need ordinary light bulbs with sockets, like those in the “tidy”. There is no need to change the LEDs; they will remain in place. Everything you need is there, you can get started.

First you need to remove the plastic, then the dashboard. Also, don't forget about the black plastic that surrounds the glass. We disassemble the standard insert, as well as the arrows. Most often, there are no holes in the new insert. Therefore, you will have to do them. For the arrows, the holes will be needed wider than in the standard trim. Otherwise, the arrows will start to stick.

Next you need to dismantle the lighting that is installed. The work should be done carefully so that the plastic is not damaged. We take out the board with the light bulbs. We install a neon light bulb instead of the usual ones, and stick a plastic protection on top. It used to have factory bulbs screwed in. Don't forget about the control unit for the new neon light bulb. You should always be careful not to confuse the polarity. If this happens, nothing will shine. Next you need to screw in the instrument lighting bulbs. This should be done in parallel to the neon lamp. We lay the wiring from the inside; first, for this you need to make holes in the partitions.

Let's check if everything is correct. The light bulbs inside should be adjusted. Next we put on the overlay and seal it. After these steps, all we have to do is paint the hands with a purchased fluorescent marker or paint. It is advisable to repeat painting after 10 minutes. After this, the arrows can be installed in their place. This completes the tuning.

Check the work, otherwise you will have to disassemble everything. If there are no problems, you can assemble everything in strictly reverse order. After such tuning, the interior of the VAZ 2109 will be equipped with a colorful panel like good foreign cars. If desired, you can use fluorescent paint to paint the dashboard trim in the place where the needle reaches its limit. It looks very nice.

How to change the backlight of the VAZ 2109 panel

During a trip, an experienced driver carefully looks not only at the road, but also at the dashboard. This is necessary to monitor the corresponding readings of the sensors that are responsible for the operation of the vehicle. It should be noted that its illumination should not tire or strain the eyes. The manufacturer equipped new cars with pale green or yellow illumination. It has a certain effect on the eyes - after a certain period of time they get tired. In this situation, it is better to replace the factory instrument lighting. For such tuning you will need a set of diodes, a soldering iron, screwdrivers with attachments, gloves, and iron pliers. Then we need to choose the color of the backlight. There are many possible options, it all depends on your imagination.

However, as always in any work, this process has its own nuances. It is recommended to install a soft white backlight if you use the car every day or for long trips. It will not tire your eyes. However, if you rarely use the car, then it is better to install light bulbs of a different, most varied color. Now let's start the installation.

First you need to completely remove the dashboard and disassemble the dashboard. To do this, unscrew the screws holding the dashboard to the body. You can find out their number by studying the car's operating instructions. It is possible that it is possible to remove the panel if you disconnect only the trim and release the steering column all the way down. Then we need to unscrew the bolts that are located at the bottom of the trim. Using a screwdriver and a flat socket, pry up the instrument cluster and remove it. You should be especially careful because you can accidentally damage the glass. After that, unscrew the bolts on the back side. We disconnect the glass, and then the plastic gasket. You do not need to touch the arrows, you should work carefully, because you can accidentally touch them or knock them down. If this happens, you will have to set them again and, what is even more difficult, adjust the sensors. When examining the back of the light bulb, you can see the location of all lighting fixtures, including LEDs.

We outline them with a marker and unsolder them from the microcircuit. We check new light elements with an adapter or battery. It is better to use LEDs because they will consume a small amount of energy and also have a long service life.

Then you need to inspect the metal antennae of the diodes so that they are intact. Otherwise the diode will not light up. We insert both antennae of the diode into the hole in the microcircuit that remains after soldering the previous light bulbs. We solder the antennae on the back of the circuit. We mount the remaining diodes in the same way. Reassembly must be done in reverse order. After starting the car, turn on the low beam. Thus, we check how the installed LEDs function.

Instrument control panel illumination

When carrying out tuning inside the car, some drivers purchase the necessary parts in specialized stores or make them themselves. When redesigning the lamp design, you need to maintain the original dimensions so that you can easily replace them with the original ones. Usually they light up the control panel for the stove and appliances. Some designers use backlighting for a voltmeter, clock, or oil pressure indicator.

To illuminate the stove, you first need to carefully remove the plastic handles of the levers that control the dampers and remove the glass. Below it is the stove itself. To do this, take any sharp object (knife or scissors) and carefully pry the glass. Prepare foil according to its size. It will be an additional source of illumination.

Fixed on the inside of the glass, it will give a very attractive appearance to the stove, and the console illumination will not be concentrated only in the place where the LED is installed next to the handle.

The next step is to remove the lamp socket from the backlight of the stove control unit. The lamp must be replaced with a purchased LED. In order for the light to spread around the entire perimeter of the stove, an LED strip is used, which is glued to the bottom. Two wires are usually soldered to the contacts, which are connected to the cartridge.

Features of backlight replacement

How to change the panel, making it a designer one? You need to be extremely careful and precise when removing and disassembling the dashboard, so as not to subsequently disturb the correctness of its readings. Often, during disassembly, the chrome plating of parts suffers. So be patient and get to work.

First, remove the dashboard panel. You can read about how to change it in the repair instructions for your car brand. Then remove the instrument cluster, disconnect the plugs, bend the speedometer cable and replace the bulbs. Gradually remove the filters from the buttons. It is better to leave the green-blue light spectrum on the panel unchanged, but replace the green filters completely.

You can make the rear window heating button illuminated orange, and the fog lamp button illuminated turquoise. This shade can be achieved by passing the white color of the LED through a green filter. The reflector can be foil secured with double-sided tape. The hazard warning lights should be red (like in foreign cars). In this case, maintaining polarity is of particular importance.

In a ring filter, using a file, you can make triangular slits through which the light will be scattered. The overall illumination pattern will become more uniform. It's time to check the performance of the LEDs. Only after this check can a constant voltage of 12 V be supplied.

Instrument needles are often replaced with special ones with backlight. This effect is achieved by a lamp located near the axis. Every driver who has basic knowledge of car mechanics and puts in a little effort can boast of a beautiful dashboard. Improve the design of the VAZ 2109 and enjoy it!

When the instrument panel on a VAZ 2109 does not light up, this is one of the common malfunctions of this unit. To fix a problem, you first have to find the cause of its occurrence.

Replacing the Dashboard Lights of a VAZ 2109 ~ AUTOTEXNIKA.RU

Repair of a high panel VAZ 2109 So, you have a need to remove the instrument cluster on a VAZ car with a recently appeared high panel.

First, we disconnect the negative cable from the battery.
Replacing the ignition switch of a VAZ 2109 - YouTube. Replacing lamps in the dashboard Styling the interior lighting of the VAZ 2110, replacing light bulbs. Replacing the steering rack on a VAZ 2109 - LuxVAZ. Next, we also disconnect the speedometer cable from the corresponding drive located on the gearbox. Now you can remove the switch that regulates the external lighting by prying it with a screwdriver. And you can now disconnect the connector from the switch and push it directly into the dashboard . Well, in order to replace the lamp that illuminates the switch, you need to squeeze the tendril from the socket with a screwdriver. -
We continue, removing both the socket and the lamp from the switch. - We remove the lamp from the socket. - We pry it with a screwdriver and take out the emergency light switch. After disconnecting the connector from the switch, you need to push it deep into the
dashboard trim . Now you will need a Phillips screwdriver. With its help, you will unscrew a pair of fastening screws for the dashboard console trim
. Replacing a light bulb in a panel of light bulbs in a panel in the dashboard. Well, we remove the trim. Now we turn to the cigarette lighter, removing the heating element, and also remove the ashtray directly from the socket.

Now let’s look around: if you are the happy owner of a receiver in your car, don’t hesitate to remove it to remove the box from the vacated slot.

To dismantle instruments, you can use two methods: 1. You can remove from the dashboard

shield. 2. Or remove the panel trim along with the shield.

How to replace the dashboard lights of a VAZ 2109

This video shows the removal and installation of a VAZ

21093i,
replacing dashboard bulbs.

VAZ 2109 replacing backlight bulbs in the instrument panel

If one or more light bulbs

in the instrument panel have stopped functioning, it is necessary to check the integrity. SO, LET'S REMOVE THE INSTRUMENT
PANEL PANEL . There are two ways to dismantle the instrument cluster: remove the panel panel or remove the panel
assembly with the panel.
We remove panel panel.
—Again, using
a screwdriver,
you need to press out 2 spring brackets.
All this is done through the radio socket. - Using the same screwdriver, you need to press out the plastic antennae (two) directly to the dashboard . - We lift the panel, after which you will have to press out the remaining third fastening bracket. - Now we disconnect the connectors from the cigarette lighter, as well as all forms its illumination, after which you need to remove the dashboard panel.—
We attach plastic antennae, as well as spring brackets, to the dashboard trim.—
When dismantling the trim together with the shield on both sides of the panel
, you need to remove the side nozzles of the ventilation system.— Take a Phillips screwdriver to unscrew one self-tapping screw on each side from the side fastening of the cover. — Now you need to unscrew 1 self-tapping screw of the main fastening from the cover, again through the radio socket. After pressing out the antennae of the lower fastening of the shield (lower), you need to remove the cover together with the shield. To replace the lamp illuminating the switch, it is necessary to remove the socket together with the lamp from inside the shield, turning it in the holder.

Well, to replace the backlight lamp for the cigarette lighter, squeeze the antennae of the cartridge holder and remove it from the device.

— Squeeze the “petals” of the cigarette lighter... — Pull it out, and then remove it from the dashboard trim

.—Using a Phillips screwdriver, you need to unscrew both screws directly to
the panel. —Now move the combination away from the dashboard
. Your next action will be to unscrew such an element as the cable union nut on the speedometer.
That is, of course, if you have a car with a carburetor engine. Our task is to disconnect the cable from the speedometer, first unscrewing the nut (cap nut). Well, you can now remove the speedometer drive cable. It comes out through the space in the front panel
. Disconnect the connectors. Replacing light bulbs in the dashboard -. Replacing rear struts (shock absorbers) on VAZ 2110, 2112, 2114, Kalina, Granta, Priora, 2109 and 2108 - Duration: 18:27. And remove the instrument cluster.

And to replace the lamps, you need to turn the socket back clockwise and remove the instrument cluster from it.

Well, assembling and installing the instrument cluster must be done in the reverse order. If you have a Peugeot car, then you will be interested in visiting the Peugeot 207 car owners club. Here you will receive the most important and interesting information on the repair, maintenance and operation of the car. Car news and reviews, new products from the global car market.

Types of panels

Instrument panels on the VAZ 2109 are of at least three types:

1. Low panel;
2. High panel;
3. Electronic panel on nines with Europanel.

On versions with a low panel, failure of the entire panel is extremely rare. This is due to the fact that here the speedometer and econometer are equipped with mechanical drives. Therefore, it is unlikely that they will fail along with the electrical component.

Why doesn't it light up?

• First, remove the cover of the mounting block and make sure that the fuse is intact. The fuse markings are located on the inner surface of the cover. You should look for fuse F16 or F5, depending on the year of manufacture of your VAZ 2109.
• If the fuse is intact, be sure to check whether the contacts of the fuse you are looking for have not oxidized. It is not uncommon for shields to fail due to broken contact.
• Check if there is power to the dashboard. To do this, you will need a warning light and the ignition on. Disconnect connector X4 in the mounting block and check for voltage at pin 3. The disadvantage of the VAZ 2109 design is that when it rains, the mounting block immediately becomes wet. This causes oxidation of the contacts in the pads, which causes the electrics to stop working. Sometimes not only the contact is oxidized, but also the board of the Nine mounting block.

Other problems that cause the backlight to not light up

Bulb burnout is the most common, but not the only reason why the dashboard backlight fails. Therefore, we are ready to offer several options for solving this problem:

• failure of the dashboard backlight brightness control. This part breaks quite rarely and requires quite complex work to dismantle and replace. Therefore, if you are sure that this is the problem, you can at least temporarily transfer the positive wire from the side lights to the backlight bus. The regulator is located on the right side of the steering wheel next to the hydraulic optical correctors;
• combustion of fuses responsible for protecting the backlight system from voltage surges and sudden increases. They will need to be replaced, since these parts cannot be restored;
• break of resistance in the panel, which is usually caused by overheating;
• poor contact where the lighting system is connected to the on-board network.

Popular faults

If we talk about the dashboard of VAZ 2109 cars, then they are characterized by certain problems. We will tell you about them, and also tell you how to act correctly in a given situation.

The instrument panel of the VAZ 2109 is not so complicated that you cannot figure it out on your own. But in the absence of experience, it is better to entrust the repair to specialists, or to enlist the support of a partner who understands this matter.