How to properly mount and connect fog lights on a VAZ 2110, 2111, 2112

Preparing for installation

Before you go to a car store, you should find out what exactly you need to purchase, taking into account the characteristics of your car.

And for this we visually define:

• What type of dashboard is installed in the cabin;
• Are there any seats (stampings) in the front bumper for installing PTF?

Note! Ready-made foglight kits have a lot of differences in the mounting method. In particular, the button for turning on the fog lights of the VAZ 2110 for cars with an old dashboard has a different shape than with a Euro-dashboard.

The kit for connecting fog lights of the VAZ 2110 has a double button for the Euro panel

Instructions for installing and connecting fog lights on a VAZ 2110, 2111, 2112 with your own hands

For independent installation and connection, you will need plumbing skills, the ability to read and understand electrical diagrams, and a willingness to incur certain material costs.

Tools and materials

To install PTF you need to have on hand:

You can purchase a ready-made set of fog lights for the VAZ 2110 or buy everything separately (cheaper option):

Self-installation and connection

Before installing the PTF, you need to remove the plugs on the front bumper and secure the fog lights with frames. The best option: do not use self-tapping screws, but M8x45 bolts with wings, which provide more durable fastening and quick dismantling.

The fog lamp is inserted into a special frame, with which it is attached to the hole in the front bumper

Installing PTF will take a minimum of time if you follow this algorithm:

After this, you need to find the terminals of fuses F4 (protects the right PTF) and F14 (protects the left fog lamp).

The location and purpose of fuses in the VAZ 2110, 2111, 2112 mounting block are indicated on the inside of the protective cover

Fuse F20 provides protection for the rear PTFs, which were originally built into the rear lights of the VAZ 2110 model range in the form of side light lamps with two filaments. In unfavorable weather conditions, the second thread is activated by a special button located on the dashboard.

At the final stage, you need to put copper connectors of the “female” type on the ends of the wires and insert them into the plug according to the attached electrical and wiring diagrams.

Legal requirements

In auto parts stores you will find a huge selection of fog lights of different shapes and sizes.

But everything depends on the existing GOST 8769-75, according to the requirements of which:

• Fog lights are only allowed to be installed in pairs;
• Each headlight must be at least 400 mm away from the plane of the side marker (measured along the outer edge of the lens);
• The distance from the road to the lower edge of the lens should not be less than 250 mm;
• PTFs should not be installed higher than the head light.

Despite the “menacing appearance”, the connection diagram for fog lights on the VAZ 2110 has been followed

Note! It is allowed to install PTF on the roof of only those cars that are used on rally tracks or in Off-Road competitions.

Installing PTF on a VAZ 2110 with your own hands

Scheme for switching on the rear fog lights of the VAZ 2110.

Circuit with one fuse (protects the circuit to the relay and headlight).

Knock sensor VAZ 2112 16 valves price.

So I decided to post a diagram and procedure for connecting fog lights on a VAZ 2.

Fog lights for VAZ 2114: Installation.

VAZ 21099 engine layout diagram. VAZ 2110 fog lamp diagram.

modification and tuning of fog lights Encyclopedia of tuning and.

replacement of the front headlight of VAZ 2113, 2114, 2115.

Wiring diagram for fog lights in VAZ 2110 World of circuits.

3) lensed PTF "" clear focused light, the ability to

DRL connection diagram. VAZ Auto Club Here is a simple connection diagram.

look at fog lights in VAZ 2114.

Wiring diagram for fog lights VAZ 21124.

Each “correct” kit contains a diagram for connecting the fog.

Pictures upon request: wiring diagram for fog lights VAZ 2110.

installation of PTF VAZ 2112 (Europanel).

Installation and connection of PTF on VAZ 21099.

Fog lights for VAZ and foreign cars in the city of Kazan, photo 7, Auto parts.

DIY installation of universal, round fog lights.

Connection to standard mounting block 2109. connection of fog lights to.

How to connect fog lights on a VAZ 2110 photos and pictures.

installation of PTF VAZ 2112 (Europanel).

b Installation and connection of PTF/b in the VAZ 2110.

affection: installing fog lights on the VAZ-2114 bumper.

how to properly connect fog lights on a VAZ 2107.

DIY installation of universal, round fog lights.

Ready-made PTF kits

Today you can find 2 types of foglights on sale, in which the light spot is formed:

• Due to scratches on the glass (classic headlight with reflector);
• Due to the lens (so-called lensed).

Complete set of lensed headlights - wiring, relay and PTF with adjustment system and plugs

Tip: Making stickers for your headlights will protect your lenses from damage.

Which of them to choose depends not only on your desire, but also on the configuration of the set.

In particular, to install PTF you will need:

• Full compliance of the kit with your car model (in this case, VAZ 2110);
• The adjustment system is easy to use (meaning, without removing the bumper or partially disassembling the headlight itself);
• Visual instructions on how to connect fog lights on a VAZ 2110.

Each “correct” kit contains a wiring diagram for VAZ 2110 fog lights

Note! Only fog lights specially designed for the VAZ 2110 can be installed on a car without any body work. Manufacturers whose products are as easy to install as possible include the German Bosch and the domestic Avtosvet Plant, the price of whose products is significantly cheaper.

The famous “Kirzhachi” are produced at the Avtosvet Plant.
So, we found out that cars of the 2110 family may differ in the way they install PTF due to the technical features of the instrument panel and front bumper.

Everything else (installation of headlights and their integration into the electrical circuit) will not create problems, because:

• The automaker has prepared the vehicle as much as possible for the installation of PTF;
• Independent work will take only 1.5-2 hours of pure time.

How to Connect Fog Lights to a VAZ 2112 Video

How to properly install and connect fog lights on a VAZ 2110, 2111, 2112

In bad weather, when fog spreads along the road or there is heavy rain, the main lighting of cars does not work well. The reason is that the headlights were designed with clear, clear weather in mind. Fog lights are designed for use in bad weather conditions. That's why they don't change in winter. To install the PTF, you do not need to contact a car service; experienced VAZ owners do this completely without outside help.

Content

What are fog lights for?

Fog. it is a mundane vortex consisting of small drops of water suspended in the atmosphere. With continuous “milky” illumination of the roadway, the lights cause the scattered light rays to be partially reflected from the droplets and blind drivers. Light cannot penetrate long distances through fog, as visibility drops sharply.

The main purpose of fog lights (FTL). formation of the correct direction of light. It can be represented in the form of a parallelepiped. wide horizontal and narrow vertical. This light flux spreads over the road surface, under the fog. Additional PTFs are provided to provide low-light illumination over roadways in adverse weather conditions.

In thick fog, proper additional lighting will mark the side road in less than 10 meters. Yes, and this is enough to ensure safety, since the situation is not very good, cars are moving at extremely low speeds.

In fog or heavy rain, the driver sees a “wall” of reflected rays, through which it is difficult to guess the surface of the road and the side of the road. It has long been noted that fog above the ground freezes with a gap of up to half a meter, because lights installed below and glowing under a smoky curtain illuminate the road even better than the main lights.

Heavy rain and heavy snow fall on the ground to better illuminate the road in bad weather. a concentrated stream of light at a low height (up to 50 cm) is yellow, in other words, white light is important. Myth, the emission range has the highest energy flux intensity compared to the light density of green, blue or violet rays.

Reliable installation and connection of fog lights VAZ 2110 and its modifications

Not all VAZ tenth series models are equipped with factory fog lights. If the driver sets up additional lighting without assistance, he has three options for solving this problem:

1. I will buy a bumper with fog lights already installed. All they need to do is connect them to the network.
2. Buy a bumper with pre-pressed sockets for installing PTF. In this case, you need to choose the right set of fog lights and install them without outside help.
3. Make holes in the plastic for the PTF yourself, repair the fog lights and connect
   them to the car network. This option allows an experienced driver to install fog lights from foreign cars on the VAZ 2110 line.

READ How to Start a VAZ 2114 Directly

PTF with corrugated (give a narrow directional light flux) or transparent (dotted) gloss will be in the “tens” range.

The requirements of the Road Traffic Rules do not contain mandatory conditions for installing PTF on a car, since domestic Russian manufacturers rarely install fog lights on the assembly line. Unfortunately, there are GOST 8769-75 and GOST 41.48-2004, which regulate the number, placement and order of switching on all lighting devices, including fog lights.

Requirements for installing PTF

Fog lights are installed according to certain rules:

• quantity. 2.4 pcs.;
• no closer than 25 cm from the surface of the sidewalk;
• no more than 40 cm from the outer contour of the headlights;
• the slots of the fog lights are made so that they are located below the top point of the low beam headlight socket;
• PTF line of sight should be: in the vertical plane 5 o 5 o, in the horizontal. 45 o 10 o.

The placement of 2 PTFs in front of the car must comply with the requirements of GOST 41.48–2004 (clause 6.3).

Reduce to fog lights Turn on only immediately with side lights.

Modern automobile brands are equipped with PTFs created by their own domestic manufacturers. For this purpose you have special sockets on the front bumper. If the fog lights are not there, then the holes are closed with plugs that are simply removed.

If PTF installation is not provided by the vehicle's equipment, the factory forged fog light holes are secured with plugs with 2 screws.

1st edition VAZ 2110, 2111 and 2112 were not equipped with holes for fog lights, so the sockets must be marked and cut out yourself in accordance with the above requirements.

Installation and connection of PTZ VAZ-2114. video 29.

Hello everyone, please follow and like the group on Instagram.

as a way to connect fog lights (PTF), running lights via a relay

Video tutorial on how to connect fog lights

In other words, running lights through a relay and an additional button. Column.

Preparing for installation

Independent connection of PTF to VAZ 2110, 2111 and 2112 requires less disassembly of the front part of the car (preferably without removing the front bumper) and the front panel (torpedo). Therefore, when preparing your fog light kit, you should find out:

• what kind of dashboard is on your car;
• Are there any stamped holes for them in the front bumper, what is their shape, or is there a way to attach the PTF.

READ DTOZH VAZ 2112 16 Valves Symptoms of Malfunction

Care must be taken not to create unnecessary problems. If the plastic bumper does not have fog lamp tubes, they can simply be made using a drill, a heated metal plate, or cut with a handsaw. The main thing is to correctly indicate the size of the finished kit using PTF fasteners, take into account the curvature of the bumper, and the structure of the material (soft, soft, hard).

The general rule must be understood. If stamped sockets for fog lights are found, then we select the shape and size of the headlights for them. If there are no holes, we first buy PTFs, then mark them according to their shape and leave space for installing fog lights.

Abstract about installing and connecting fog lights on a VAZ 2110, 2111, 2112 house

Self-assembly and connection will require the skills of a mechanic, the ability to read and understand electronic circuits, and the willingness to bear some material costs.

Tools and materials

To install PTF you must have:

• multimeter;
• control light;
• combination screwdriver with slotted and cross-shaped working body;
• pliers;
• forceps;
• keys 8x10, 12x14;
• light hammer;
• electrical insulating tape;
• shrink packaging.

Buy ready-made fog lights for the VAZ 2110 or buy everything separately (cheaper):

• PTF. 3.2 pcs.;
• the frames on the right and left are made of plastic fog lights VAZ 2110. 3.5 pcs.;
• button with yellow backlight;
• relay;
• wire with 2.4 copper cores of different colors with a diameter of 0.5 mm (for more massive lamps it is better than 0.75 mm in diameter). 5 m;
• female connecting plugs are narrow (single). 8 pcs.;
• Wide (double) female/male mat for connection to each fog light. 3.5 pcs.;
• Bolts M8x45. 4 things.;
• "Lamb" with M8 bolts. 4 things.

Homemade and tied

Before installing the PTF, remove the plugs on the front bumper and secure it with the fog lights. Ideal: do not use screws, but M8x45 thumb bolts for more secure fastening and faster disassembly.

The fog lamp is inserted into a special frame and, with the help of a passenger, is fixed in the opening of the front bumper

Installation of this method requires installation of PTF at the cinema level:

1. Connecting to the electrical network should begin by pulling the wires from under the dashboard into the engine compartment. They should first be placed in a protective corrugation.
2. The operation described above requires partial disassembly of the torpedo. On a VAZ 2112, the factory wiring has this option for connecting the PTF, so you only need to find the connecting blocks on the front bumper, which are located next to the plugs.
3. Remove the positive terminal from the battery.
4. Open the relay assembly and fuses (located in the lower left corner of the control column next to the clutch pedal)
5. Remove the screw using a screwdriver and remove the unit.

READ How to Turn on the Windshield Washer on a VAZ 2107

The fuse box is located on the left side of the driver's left foot

Then you need to find fuses F4 (protects the right PTF) and F14 (protects the left fog).

The location and purpose of fuses in the VAZ 2110, 2111, 2112 mounting block are indicated on the inside of the protective casing.

Fuse F20 protects the rear PTFs, which were originally included in the rear dimensions of the VAZ 2110 type in the form of two-way parking lights. In adverse weather conditions. Another reason is that the thread is cut by a special button located on the dashboard.

The final step is to apply copper connectors to the end of the wires and connect them to the plug according to the added electronics and wiring diagrams.

Electronic diagram for connecting fog lights VAZ 2110, 2111 and 2112 using an illuminated button and relay

The location of the fog light power button depends on the type of front panel. Of course, there are certain aspects to combining PTF old and European panels.

Normal connection under the fog lights of the fog lights on a VAZ 2110 and VAZ 2111 with the same front panel without connecting the PTF switch relay

On VAZ 2112 models with a European panel, the plant laid wires for connecting fog lights at the car plant.

Connection diagram of PTZ VAZ 2112 to factory wiring connected to PTF connectors, mounting block, relay and backlit power button (connected without outside help)

A common way to connect and connect fog lights

If you install this order, installing the fog lights will take about 1-1.5 hours:

1. The PTF wiring is laid on top of the main wiring, which runs along the left front fender.
2. The PTF power button inserted into the socket on the instrument panel must be removed from the right fuse according to factory recommendations. In this case, the PTF will remain on when the ignition is turned off. Disabling them using their own button will quickly drain the battery. However, if the PTF is powered from the headlight power button or directly from the ignition switch, they light up when the ignition key is turned on.
3. Insert the plugs into the fog lights and turn them on. If the PTF on the VAZ 2110 and its modifications do not light up, this indicates an error in the connection diagram. So you should check for a new one that is a member of the chain.

video: connect fog lights VAZ 2110

Source

Self-installation

Electrical connection

Having purchased a ready-made PTF kit, you can begin to integrate it into the standard VAZ electrical wiring system:

• Disconnect the battery (remove “+”);
• Open the fuse box and use a screwdriver to unscrew 1 screw and remove the block into the passenger compartment;

The VAZ 2110 fog light switching circuit is protected by fuses

• We unfold the block and find the terminals of two fuses F4 and F14. The first is responsible for protecting the right headlight, the second – the left;
• The block also contains fuse F20, which is responsible for the operation of the rear PTFs;

Note! The connection diagram for the rear fog lights of the VAZ 2110 is initially present on all models, and consists of two-filament lamps in the side light unit.

• We insert the copper wire connectors from the kit according to the attached diagram;
• Separately, we bring out the wire for the button into the instrument panel and install it;
• We lay the wires through the partition into the engine compartment;
• Putting the fuse block back together.

Bumper installation

• Remove the plastic plug and insert the wiring with the connector into the hole;
• We connect it to the base and install the fog lamp for the VAZ 2110 in the bumper;
• Take a Phillips screwdriver and screw the headlight with 2 self-tapping screws;
• We pre-adjust its position;
• We secure the wiring in the engine compartment, leaving some slack for replacement (for example, a burnt-out lamp);
• We connect the battery and check the quality of the work performed.

The photo shows the process of fixing the PTF in the front bumper.
All that remains is to adjust the correct direction of the light flux. You will find information about this procedure in other articles on our website dedicated to AvtoVAZ models.

Independent connection of fog lights on a VAZ 2110: studying the installation features

The changes AvtoVAZ constantly makes to its conveyor models lead to the fact that, upon detailed examination, cars that are identical according to the documentation have significant differences.
For example, not all factory VAZ 2110 have fog lights (PTF). And the owners have questions about what needs to be done to connect them with their own hands? This article will discuss whether the connection of fog lights on a VAZ 2110 can “survive” without disassembling the front part of the car and the instrument panel.

Preparing for installation

Before you go to a car store, you should find out what exactly you need to purchase, taking into account the characteristics of your car.

And for this we visually define:

1. What type of dashboard is installed in the cabin;
2. Are there any seats (stampings) in the front bumper for installing PTF?

Note! Ready-made foglight kits have a lot of differences in the mounting method. In particular, the button for turning on the fog lights of the VAZ 2110 for cars with an old dashboard has a different shape than with a Euro-dashboard.

Legal requirements

In auto parts stores you will find a huge selection of fog lights of different shapes and sizes.

But everything depends on the existing GOST 8769-75, according to the requirements of which:

1. Fog lights are only allowed to be installed in pairs;
2. Each headlight must be at least 400 mm away from the plane of the side marker (measured along the outer edge of the lens);
3. The distance from the road to the lower edge of the lens should not be less than 250 mm;
4. PTFs should not be installed higher than the head light.

Note! It is allowed to install PTF on the roof of only those cars that are used on rally tracks or in Off-Road competitions.

Ready-made PTF kits

Today you can find 2 types of foglights on sale, in which the light spot is formed:

1. Due to scratches on the glass (classic headlight with reflector);
2. Due to the lens (so-called lensed).

Tip: Making stickers for your headlights will protect your lenses from damage.

Which of them to choose depends not only on your desire, but also on the configuration of the set.

In particular, to install PTF you will need:

• Full compliance of the kit with your car model (in this case, VAZ 2110);
• The adjustment system is easy to use (meaning, without removing the bumper or partially disassembling the headlight itself);
• Visual instructions on how to connect fog lights on a VAZ 2110.

Note! Only fog lights specially designed for the VAZ 2110 can be installed on a car without any body work. Manufacturers whose products are as easy to install as possible include the German Bosch and the domestic Avtosvet Plant, the price of whose products is significantly cheaper.

So, we found out that cars of the 2110 family may differ in the way they install PTF due to the technical features of the instrument panel and front bumper.

Everything else (installation of headlights and their integration into the electrical circuit) will not create problems, because:

1. The automaker has prepared the vehicle as much as possible for the installation of PTF;
2. Independent work will take only 1.5-2 hours of pure time.

Self-installation

Electrical connection

Having purchased a ready-made PTF kit, you can begin to integrate it into the standard VAZ electrical wiring system:

1. Disconnect the battery (remove “+”);
2. Open the fuse box and use a screwdriver to unscrew 1 screw and remove the block into the passenger compartment;

1. We unfold the block and find the terminals of two fuses F4 and F14. The first is responsible for protecting the right headlight, the second – the left;
2. The block also contains fuse F20, which is responsible for the operation of the rear PTFs;

Note! The connection diagram for the rear fog lights of the VAZ 2110 is initially present on all models, and consists of two-filament lamps in the side light unit.

1. We insert the copper wire connectors from the kit according to the attached diagram;
2. Separately, we bring out the wire for the button into the instrument panel and install it;
3. We lay the wires through the partition into the engine compartment;
4. Putting the fuse block back together.

Bumper installation

1. Remove the plastic plug and insert the wiring with the connector into the hole;
2. We connect it to the base and install the fog lamp for the VAZ 2110 in the bumper;
3. Take a Phillips screwdriver and screw the headlight with 2 self-tapping screws;
4. We pre-adjust its position;
5. We secure the wiring in the engine compartment, leaving some slack for replacement (for example, a burnt-out lamp);
6. We connect the battery and check the quality of the work performed.

All that remains is to adjust the correct direction of the light flux. You will find information about this procedure in other articles on our website dedicated to AvtoVAZ models.

Conclusion

All that remains is to wish you trouble-free driving in poor visibility conditions. And in the video presented in this article you will find additional information on this topic.

Features of the VAZ 2110

The VAZ 2110 car is not very different from its younger brothers of the following modifications, but there are still some differences:

1. This model does not have front fog lights. Moreover, the car bumper may not even have seats for PTF.
2. For some reason, the car has rear fog lights, which seems strange: there are rear ones, but no front ones.
3. The VAZ 2110 can be equipped with different types of panels: standard (also called old) and europanel. In the first case, there is no space for installing the PTF power button, but there are several slots for installing additional switches. In the case of the Europanel, the PTF button can be installed in a place previously provided for this, and the fuse panel has sockets for connecting fog lights.

Before you go to the store to buy an anti-fog kit (more about it below), carefully examine your car and find out what panel is installed in it, whether there are seats for fog lamps, what shape they are, etc. Otherwise, you may buy the wrong kit or the wrong fog lights.

Instructions for connecting fog lights on a VAZ-2110

To avoid having to redo a lot later, during connection, follow the sequential instructions:

1. Open the fuse box cover, unscrew 1 screw and open the power supply.
2. Find 2 wires, the length of which reaches 15 cm; the cable connectors are called “mother”. Determine which wire is permanent - checked with a test lamp, the cable should be pulled to the relay on the leg.
3. The red wire indicates the positive from the relay. To carry out the installation quickly and without complications, it is better to take the connector with the 2nd “mother” and extend them with cables up to 30 cm, marking the “female” connector.
4. Distribute the yellow and yellow-black cables into a white plug, it is located on the power supply.
5. Connect the connector with the 2nd wire and the “female” connector to the power supply unit and connect it to the 2nd “male” connector, it is also characterized by 2 wires of yellow and black-yellow colors, the latter is located behind the trunk opening button.
6. Black wires most often mean negative and are connected to the relay leg.
7. It is also important to identify the control wire for turning the fog lights on and off. This can be done in several ways, for example, by marking a wire running from the lights without a power button, so the headlights will light up as soon as the lights are turned on. Another way is to move from the dimensions through the button. The headlights can also depend on the ignition; the PTF power button will indicate a plus and only when the key is pressed will the headlights turn on. The latest option is considered the most convenient.
8. To install the PTF, remove the plug and insert the headlights directly into the bumper.
9. Secure the headlight cover material.
10. Take a Phillips screwdriver and turn a couple of self-tapping screws holding the cladding fasteners.
11. Connect the block to the cable. The device is now connected.

Requirements for installing PTF

How legal is it to independently install fog lights and will it not cause problems when meeting with traffic police officers? Let's consider excerpts from the standards by which PTF is established by the manufacturer (GOST 8769–75 and GOST 41.48–2004):

1. Number of lanterns – 2 pcs.
2. Installation height – not lower than 25 cm from the road surface, but lower than the low beam lights.
3. Installation in width - no further than 40 cm from the side lights.
4. The vertical coverage angle is 5-10 degrees.
5. The lighting angle of the road surface (horizontal) is 45-55 degrees.
6. PTFs are turned on only together with the side lights.

If PTFs are installed according to these rules, then no problems will arise with police officers.

Correct installation and connection of fog lights VAZ 2110 and its modifications

Not all models of the tenth row of VAZ are equipped with factory fog lights. If the driver independently tunes additional lighting, he has three options for solving this problem:

1. Buy a front bumper with fog lights already installed. They just need to be connected to the car network.
2. Buy a front bumper with ready-made stamped sockets for installing PTF. In this case, you need to choose the right set of fog lights and install them yourself.
3. Make holes in the plastic for the PTF yourself, attach the fog lights and connect them to the car’s network. This option allows an experienced driver to install fog lights from foreign cars on the VAZ 2110 model range.

The “tens” model range is equipped with PTFs with corrugated (provide a narrowly directed light flux) or transparent (gives spots of light) glass.

The requirements of the Road Traffic Regulations do not contain a mandatory condition for installing PTF on cars, so domestic manufacturers do not always install fog lights on the assembly line. But there are GOST 8769–75 and GOST 41.48–2004, which regulate the number, location and order of switching on all lighting devices, including fog lights.

Requirements for installation of PTF

Fog lights are installed according to certain rules:

• quantity - 2 pieces;
• no closer than 25 cm to the surface of the road surface;
• no more than 40 cm from the outer contour of the headlights;
• sockets for fog lights should be located below the top point of the low beam headlight socket;
• PTF line-of-sight angles should be: in the vertical plane 5o+5o, in the horizontal plane - 45o+10o.

The location of two PTFs in the front lower part of the car must meet the requirements of GOST 41.48–2004 (clause 6.3)

The fog lights turn on only at the same time as the side lights.

Modern brands of vehicles, as a rule, are equipped with PTFs, which are installed by the manufacturers themselves. For this purpose, special sockets are provided on the front bumper. If the fog lights are not installed there, the holes are closed with plugs that can be easily removed.

If the installation of PTF is not provided for by the car, the factory stamped holes for installing fog lights are closed with plugs on two screws

The first editions of the VAZ 2110, 2111 and 2112 were not equipped with holes for installing fog lights, so the sockets must be marked and cut out with your own hands, taking into account the above requirements.

Preparing for installation

Self-connection of PTF on VAZ 2110, 2111 and 2112 involves minimal disassembly of the front part of the car (preferably without removing the front bumper) and the front panel (dashboard). Therefore, before buying a ready-made set of fog lights, you should find out:

• what kind of dashboard is on your car;
• Are there any stamped holes for them in the front bumper, what is their shape, as well as the method of attaching the PTF.

You need to act carefully so as not to create unnecessary difficulties for yourself. If there are no sockets for fog lights in the plastic bumper, then they can be easily made using a drill, a heated metal plate, or cut out with a hand jigsaw. The main thing is to correctly mark the size of the finished PTF kit with fasteners, take into account the curvilinearity of the bumper, the structure of the material (fragile, soft, hard).

You can make your own nest in the bumper using a drill and a thin drill with a diameter of 2–3 mm, often placing the holes along the contour

You need to remember a simple rule. If there are stamped sockets for fog lights, then we select the shape and size of the headlights to match them. If there are no holes, then first we buy PTFs, and then mark them according to their shape and make places for attaching the foglights.

Types of instrument panels and location of fog lamp buttons

As I noted above, depending on the modification, VAZ 2110 cars are equipped with two types of panels: the so-called old panel and the European panel. If you have a Europanel installed, then the place to install the button for turning on the fog lights is located to the left of the steering wheel, and this button is located in close proximity to the button for turning on the side lights.

On some modifications of the Europanel, the buttons for sidelights and fog lights may be located one above the other:

On a regular, old panel there is no special place for installing a PTF switch, but there are places for installing additional buttons for any purpose, including for connecting PTF. They are closed with plugs and are located on the switch panel between the driver and passenger.

On cars with an older panel, the space for additional buttons is located to the right of the driver

The indicated installation locations for the fog light switch on a VAZ are recommended, but not required. You can install the PTF button in any place convenient for you.

We connect fog lights on a VAZ-2110 with our own hands (+ diagram)

Good fog lights are a useful and often necessary thing. They come as standard equipment to almost all modern cars, including the most budget models. Unfortunately, the VAZ-2110 was deprived of foglights in the basic configuration, and this inexpensive option is the most popular among us. Today we will increase the level of equipment of our top ten - we will select and install fog lights according to several schemes.

Selection of fog lights for the VAZ 2110

The range of PTFs for the VAZ 2110 today is quite wide: large and small, round and square, yellow and white. Which ones to choose? Everything here will depend on your taste and financial capabilities, but I still dare to give some advice.

1. Yellow light is less absorbed by water (and fog and rain are water). This means that yellow PTFs will produce a higher quality light spot than white ones of the same power, and at the same time they will not dazzle oncoming drivers.
2. The shape of the headlights does not matter, the main thing is that they should fit the seats of your bumper as best as possible.
3. You should not buy very expensive headlights from famous brands. Most often, such companies charge a lot of money just for the fact that they are famous (the so-called surcharge for the brand).
4. Before purchasing, take the headlight in your hands and carefully examine the quality of the body and glass. Even by its weight and appearance, you can feel whether it is a worthwhile thing or junk that will fall apart after 100 km of run.

Below I will give some common and affordable PTF models for the VAZ 2110 that really deserve attention.

How to properly mount and connect fog lights on a VAZ 2110, 2111, 2112

In bad weather, when fog spreads over the road or heavy precipitation falls, the main vehicle lighting does not do its job well. The reason is that the main headlights were designed for clear, good weather. Fog lights are installed for use in bad weather conditions. That is why they are indispensable in the cold season. To install the PTF, it is not necessary to contact a car service; experienced VAZ owners can easily do it themselves.

Optics installation

• First you need to choose a place for installation - as a rule, this is a special compartment under the front bumper. In the case of the “ten” there are several options for fog lights. They can be corrugated, which diffuse the light, or transparent, in the latter case the light will come out in spots. The transparent option today is more fashionable and in demand among our compatriots, but it is less useful.
• In the engine compartment, disconnect the wires that are connected to the fluid control regulator and the washer expansion tank. To do this, unscrew the washer fixing nut and remove the block with wires, which is located under the left side member.
• For the Ш-1 connector you will need three cables - one yellow and two black-yellow.
• After this, you will need to cut two pieces from the yellow cable - they should be pulled into the vehicle interior. The wiring is thoroughly cleaned and male terminals are connected to it. Having completed these steps, the connectors must be connected to the block in such a way that the marked cable is connected to the black and yellow wire. Next, the block must be connected and two yellow cables attached to the harness. Having done this, the washer reservoir can be installed in place.
• After this, you will need two more pieces of wire, each should be 0.5 m long. You need to connect a ground terminal to these wires, and then fix it to the stud along with the ground cable from the optics.
• The cable from the PTF must be pulled from the front side member and brought out to where the lamp itself will be fixed. A ground terminal must be connected to each cable.
• After these steps, the brackets are mounted on the bumper itself, and the terminal blocks are connected to the wires. The final stage will be the installation of light bulbs in the lanterns (the author of the video is the proVAZ-2110 channel).

READ Replacement Thermostat Lada Kalina 8 Valves

Installation process

Before installing fog lights on a VAZ 2110, you should carefully consider purchasing them.

But don’t rush to the store, but first figure out what kind of front bumper your car is equipped with. If the bumper has seats for PTF (they are usually closed with plugs), then everything is in order. Measure your seats and go to the store.

If the installation of fog lights on your bumper is not provided, then you will either have to buy a new bumper or do it yourself. Here everything will depend on your desires and capabilities, since there are always PTFs on sale with decorative overlays that can be installed on almost any bumper.

In some modifications of bumpers there are no holes for fog lights, but the places for their installation are stamped. In this case, first select the headlights that will fit your bumper, and only then cut the mounting holes for them.

This can be done using a conventional drill by drilling a series of holes around the perimeter of the future seats.

After the hole is cut or the plugs are removed, install the PTFs in their places, following the instructions and using the fasteners included with the headlights. Typically, headlights are attached through a decorative trim using two screws.

Connection to electrical circuit

So, the VAZ fog lights are installed in their regular places, all that remains is to connect them to the VAZ hog network. According to the current rules (see above), PTF can only be turned on together with the side lights. If you turn on the PTF, but forget to turn on the “dimensions”, then this will already be a violation.

The fact is that the fog lights are installed quite close to each other, and in the dark the oncoming driver will not be able to correctly assess the width of your car. That is why the side lights must be on when the PTF is operating.

To prevent this from happening, the connection diagram for fog lights in a VAZ is assembled in such a way that they cannot be turned on with the lights turned off. Despite its apparent complexity, the circuit is quite simple, and anyone with basic knowledge of electrical engineering can understand it.

Typical electrical connection diagram for PTF VAZ 2110

When the headlights are turned on, voltage from them is supplied to the fog light switch, allowing it to start working. When you press it, voltage is supplied to the electromagnetic relay, which connects the VAZ fog lights to the +12 V bus. The second wire supplying the headlights is connected to the car body, which, as you know, is the negative wire for all VAZ electrical equipment.

At the same time, the supply voltage is supplied to the indicator lamp, indicating that the PTFs are turned on. So that in the dark the fog light switch can be easily found on the panel, it is illuminated by a miniature pilot lamp. It can be connected in parallel to any panel backlight lamp.

If you are not very experienced in electrical engineering, then you may have a question: why a relay if voltage can be supplied to the headlights directly from the switch? The fact is that fog lights consume quite a lot of current, which neither the PTF switch nor the headlight switch wiring simply can withstand.

In the best case, when turning on the PTF without a relay, the fuse for the dimensions will burn out, in the worst case, the wiring of the dimensions and the equipment that powers them will burn out.

Theoretically, the scheme is clear, but how to implement it in practice? As I said above, there are several modifications of the VAZ 2110, 2111, 2112 that are not equipped with fog lights. Some have old-type panels, others have so-called Europanels. Let's consider the installation procedure for both cases.

Connecting PTF in a car with an old panel

Based on the above diagram, in order to organize fog lighting on this VAZ model, in addition to the fog lights, you will have to buy an installation kit consisting of the following elements:

• PTF power button;
• PTF turn-on relay;
• set of installation wires;
• fuse(s);
• accessories (ties, terminals, brackets, adapters, etc.);
• connection instructions.

Kit for connecting fog lights for VAZ 2110 with an old panel

When buying a kit, choose the one that is designed specifically for the standard VAZ 2110 panel. The standard and Euro panels differ in the shape and size of the PTF button seats.

If the kit is in hand and the illuminators are installed, all that remains is to assemble a circuit that will look like this:

PTF connection diagram for the old panel (pin 86 is connected to the car body)

The only problem that will have to be solved is to find a place for the relay, since the car’s design does not imply a standard mounting. You can place it anywhere: even under the panel, even in the engine compartment away from the heating parts of the engine.

If the kit does not come with a coil of wire, but with ready-made wires with connectors, then when installing the relay, be guided by the length of these wires.

Option for relay location for fog lights in the engine compartment

All that remains is to lay the wires and, if necessary, press the knife pads that come with the kit onto them (ordinary pliers will do), and then assemble the circuit. When laying wires, try to run them close to the standard harnesses - this is the safest place for them. They will not fray or fall on the hot parts of the engine. At the same time, take the length of the wires with a small margin and often grab them to the body or the standard wiring harness with the clamps included in the kit.

Be sure to install the fuse included in the kit! In the event of an accident in the wiring of the fog lights, it will save the car from fire.

Connecting PTF in a car with a Europanel

If your car has a Europanel installed, then the connection diagram for the fog lights changes somewhat, since the manufacturer has provided for their installation. In addition, the kit for connecting fog lights for VAZ, as I noted above, should have a button of a slightly different shape than for cars with a regular panel.

Kit for connecting fog lights for VAZ 2110 with Europanel (the difference is in the shape of a button)

After the wires from the lights are brought into the cabin, open the wiring box, which is located on the left under the steering wheel:

The VAZ 2110 mounting box with Europanel is secured with two self-tapping screws

Find the locations of fuses F4 and F14. If they already have 10 A fuses, then everything is in order. If not, then install the ones included with the kit. They will be responsible for the safe operation of the right and left headlights, respectively.

Marking of fuses VAZ 2110 with Europanel

All that remains is to assemble the circuit by connecting the relays, illuminators and button according to the diagram above and connect it all to blocks Ш1 and Ш3.

PTF connection diagram for VAZ 2110 europanel

Where can I find these pads? They are located on the side opposite the fuses in the same mounting block, and they are numbered as follows:

Numbering of mounting pads for VAZ 2110 with Europanel

After installing and connecting the fog lights, do not forget to adjust them correctly and make sure that they shine in the right direction. Otherwise, they will not so much help in bad weather as hinder you and oncoming drivers.

So we figured out how to install non-standard fog lights on a VAZ 2110 with our own hands. It turns out that this is not difficult to do yourself, and installing them is completely legal and even desirable. After all, good lighting on the road is additional safety for all road users.

Fog lights VAZ 2110 wiring diagram

Wiring diagram for fog lights.

connection option 1

1) Open the fuse box, then unscrew the screw, pull it out and turn the fuse box over. Wires marked in green do not come from the factory and must be added.

Reverse side of the fuse box.

2) From the bundle of wires included in the kit, cut off two wires, 15 centimeters each. At the ends of both wires we attach female connectors.

The red wire, marked 1 in Figure 2, is positive, you can even check it with a test light. We stretch it to the leg number thirty on the back of the relay.

We connect the first positive wire.

3) The wire labeled number 4 in the figure as 2 is the pole running from pin 87 back to the fuse box.

We connect the second positive wire.

4) We connect the red positive wires to the fuses in Figure 5 (they are intended for PTF), after which they separate one at a time to the right and left headlights.

Fuses for PTF (10 amps each) installed from the factory.

5) We mount the wires as shown in Figure 7. We attach thirty-centimeter wires with “mothers” at the ends to the double-female connector.

We create a convenient installation connection.

6) We insert the wires with single “mothers” into the white plug, in the places marked with circles on the fuse block.

Connection points for single females on the fuse block.

7) We remove the double female connector from the fuse block and connect it to the double male connector, which is located behind the trunk release button.

We connect our connector to the connector behind the trunk release button.

The black wire numbered 3 comes from pin 86 located on the relay and is a minus. It is best to draw the negative from the top of the fuse block. There are already factory black wires there, inserted under the 10 nut. The wire marked with the number 4 is responsible for turning the PTF on and off.

Negative and PTF switching wire.

Several options for where to run the PTF control wire.

1) From the side lights directly, when the side lights are turned on, the PTF turns on.

2) From dimensions with an additional button. Then turning on the dimensions only supplies power to the button, and the button itself turns on the PTF.

3. We run the wire from the ignition switch through the button, as in method 2. This is the most convenient option.

In photo No. 11, number 1 indicates the PTF turn-on relay, and number 2 indicates the place for the electric lift relay. We take two wires from it, extend them and connect them to the headlight switch button

One of them (pink thin in our case) when you turn on the ignition, a “plus” will appear, and the black wire will be a “minus”. To correctly connect the PTF, it is important to know that the left output is located near the radiator, under the left headlight, and is easily secured with a clamp to the car body. The right exit is located symmetrically under the right headlight.

Why is this necessary?

Modern fog lights provide significantly more “penetrating” light through fog and rain and better illuminate the road surface. Firstly, PTFs produce a flatter luminous flux, spreading above the ground and spreading more in width than in height.

This was not done in vain. The fact is that due to the discrepancy in the temperature of the air and the ground (the ground is warmer), the fog rarely reaches the road itself, which means that with such headlights on the VAZ 2110 you will see the road you are driving on at least ten meters further ahead low beam headlights.

Secondly, due to the beam width of the fog lights, you will see the roadside and markings. This will prevent you from “flying off” the road, which is not uncommon in fog.

Thirdly, you will not blind oncoming cars, but you yourself will be visible to other road users, if, of course, the adjustment is made correctly. This means that the probability that another car will not crash into your VAZ 2110 increases.

Color meaning

Some people, in the old fashioned way, believe that it is better when the fog glass is yellow. But this is not true. Most leading manufacturers today produce transparent white fog lights, and they are not only as good as yellow ones, but often superior to them.

On the VAZ 2110 you can install corrugated or transparent glass. The latter are for some reason more fashionable, although less useful, since they shine in spots, while the corrugated ones give a more directed beam, which really increases visibility in bad weather.

Question about glass color for fog lights

On old cars, the glass of fog lights was yellow , so many people think that it should be like this now, it is more correct and more efficient.

In reality, everything is different. Today, auto industry leaders use exclusively clear glass for fog lights, which are superior to yellow ones in many components.

The current fog lights on the VAZ 2110 are available in two versions - transparent and corrugated. Most people choose transparent glass, although in fact, corrugated glass is better. They provide a clear directional beam that can show its best side during fog or rain.

Buying what you need

You can, in principle, buy a ready-made set along with wires, but many believe that if you buy everything separately, the number of installation options increases, and it will all cost less. So, we buy:

• Set of headlights (2 pieces);
• Plastic pads;
• Headlight frames;
• A key and a yellow indicator for it;
• Relay;
• Wires. It is better to purchase ones from an electrical equipment store, so that there are two copper conductors with double insulation (ShVVP-2 is suitable). A cross section of 0.5 mm will also be normal, but if you want to install lamps of higher power, take 0.75 mm;
• Terminal for installation to ground;
• Wide as well as narrow terminals, called mother/father. When purchasing them, it is advisable not to take them complete with wires. Installation will be more convenient if these terminals are crimped with pliers already on the connections of the installed wires.

Kit for connecting fog lights on VAZ 2110

Note: if your VAZ has an old-style dashboard, then it is better to buy a PTF 2110 kit, but for a new, so-called EURO, it is more convenient to connect PTF 2115.

You can, of course, vary it, but we are talking specifically about the convenience of the location of the buttons. Regarding the power of the lamps, 55 W is enough, no more is needed. Also keep in mind that very cheap fog lights will not last long.

Materials and tools

You can easily buy a ready-made PTF kit with all the wires, and then you won’t have to figure out where the fog light relay is located on a VAZ 2110. However, if you purchase spare parts separately, this will diversify the installation options, plus it will allow you to save money.

Connection kit

Therefore, you need to purchase the following:

• Two sets of headlights;
• Plastic pads;
• Headlight frames;
• A key with a yellow indicator for it;
• Relay;
• Wiring. Choose an option with two copper conductors and double insulation, for example ShVVP2. A cross section of 0.5 mm is suitable, but if the lamps are powerful, 0.75 mm is better;
• Ground terminals;
• Female/male terminals - wide and narrow terminals.

It is not worth taking the mother-father complete with wires. It is better to crimp them using pliers when the wiring is already connected.

Pay attention to what kind of dashboard you have. If it is an old model, buy a set of fog lights for the VAZ 2110, and if it is a Euro dashboard, then it is better to use the PTF for the VAZ 2115.

As for the light bulb, 55V is more than enough power. We strongly do not recommend buying cheap fog lights, since their service life is very short.