Replacing the door lock cylinder on a VAZ 2109. when the time has come

The problem with the VAZ-2109 is that over time the door becomes loose and the operation of the locks is disrupted. In most cases, adjustment and adjustment of the lock is necessary. The situation is more complicated when the lock simply jams. This often happens on the driver's side. In this case, it is worth replacing the lock, but do not knock it out with a wheel wrench. As a temporary measure, the door lock cylinder on a VAZ-2109 car can be replaced.

Door lock device

To understand how to change the door lock on a VAZ, it is important to understand the structure of the mechanism itself. The larva is a metal core that is activated when the key is turned in the well. Protection is provided by locking the internal teeth. If incorrect operation of the locking system is noticed, the entire lock or its cylindrical part is replaced. When the key enters the device, the internal pins begin to move. When problems arise when opening/closing the mechanism, it means that the teeth do not fit into the grooves.

If the pins diverge in different directions when opening, then when closing, a disconnective displacement occurs. This encoding is activated when the key is turned. The reasons for the breakdown may be as follows:

• creak;
• difficulties when inserting and removing the opening object;
• jamming;
• internal or external damage to the cylinder;
• The key does not go all the way into the hole.

When the lock is used for a long time, parts wear out. In order not to completely change the closing device, you can remove the cylinders and install a new one.

How to install euro handles on a VAZ 2109, 2114.

To install the Euro handle on a VAZ 2109, 2114, we squeeze it out and try to insert it into the socket. The fit is a little tight. After installing the handle in the technological hole, you need to push it a little in the direction of travel of the car and the handle completely sits in place. Now you can screw it on

Door opening rods are included with the Euro handles. Two short ones go to the rear doors, two long ones to the front ones. We put on the required rod and adjust it by unscrewing or screwing the plastic attachment onto the rod. We try to open and close the door. If the door does not open, then unscrew the plastic cap a few turns; if the door does not close, then tighten it.

All! Euro pen installed! Now all that remains is to assemble the door card. It is assembled in the reverse order of disassembly.

How to install Euro handles on a VAZ 2109, 2114 is no longer a secret for you!

Tools

To repair or replace a car lock, you need to prepare:

• flat-head and Phillips-head screwdrivers;
• pliers;
• socket wrench 8;
• silicone grease;
• larva

If desired, you can immediately replace the standard part with a European pen, which is purchased in advance.

Repair work is carried out in a well-lit room and at a comfortable temperature.

We repair “Nine” locks ourselves

Let's say the key in the VAZ-2109 lock does not turn or, conversely, turns and does not unlock the door.
Repairing car locks involves one of the following actions: replacing the cylinder (cylinder), replacing or repairing the internal lock. In official manuals, by the way, it is recommended not to repair the internal lock mechanism, but to replace it. Be that as it may, you first need to get to it, for which you remove the door trim. Each of the actions required for dismantling is further illustrated in the photo. The entire sequence must be considered in order. The door lock cylinder on a VAZ 2109 is replaced in the event of a malfunction. We list the most common reasons:

• Lost key;
• The latch that secures the lock itself to the rod connecting it to the central lock has fallen off;
• Breakage specifically of the larvae. Due to the design features, it cannot be repaired, only replaced;

• Broken wire.

In any of these cases, the lock will have to be disassembled. Don't delay this. Timely repairs will save you from hassle and preserve your property.

Repair or dismantling of interior door locks

When replacing the rear door lock of a VAZ 2109, it is important to follow the algorithm of actions:

1. To remove the handle, use a screwdriver to unscrew two bolts: top and bottom.
2. The cover, plug and casing are removed. The facing material is secured with special latches. It is important to dismantle them carefully so that the plastic elements do not break.
3. The panel is removed and the external fasteners are removed using a size 8 wrench.
4. Access to traction is gained. It can be unscrewed freely using a screwdriver.
5. The handle is removed along with the rods, the tip is dismantled.
6. The core of the cylinder device opens.
7. To change the cylinder, it is important to remove the return spring.
8. After installing the new core, we return the spring to its place. A pin is installed on the tip of the rotary rod.
9. The lubrication of the elements and the functionality of the mechanism are checked.
10. The assembly is performed using the reverse algorithm.

Sometimes it is necessary to replace the wires that are connected to the lock. If a small break is detected, the electrical wiring is partially changed.

Replacing the Door Lock Cylinder of a VAZ 2109

Step-by-step replacement of VAZ-2109 lock

The problem with the VAZ-2109 is that over time the doors become loose and the locks work. In most cases, you will need to adjust and adjust the locking. Things get complicated when the Castle

it just jammed.
Replacing the timing belt VAZ 2109 1.5 l 8 valves p. This often happens on the driver's side. Replacing the door lock cylinder | VAZ 2110 repair. In this case, it is worth replacing the lock, but do not knock on it with a wheel wrench. As a temporary measure, lock cylinders on a VAZ-2109 car can be replaced.

Repair of interior door locks

Lost keys or locked out. An unpleasant situation for any car owner. Do not break doors or locking mechanisms. Open the door, being careful not to break the rods and locking mechanism of the housing. Lock UAZ 452 Door analysis, lock and replacement of the cylinder lock, how to replace the door handle on a UAZ. Replacement of silent blocks of crab vases 2109 | auto forum. Then move on to the rest of the work. A summary of the removal and replacement of European larvae is as follows:

1. Remove treatment from door . This job doesn't require a lot of work, but be careful not to damage the material.
2. Disabling kernels. one of the most difficult parts of the job. Gather the bottom with pliers and remove from the handle. Then it is easy to insert it back. Replacing the ignition cylinder cylinders on a BMW. Remove the ignition switch on a BMW e39? How to remove. To remove the top, press the handle with a screwdriver, feed the unwanted wire through the rod and pull it sharply. Without a screwdriver, the rod will bend.
3. Unscrew the handle using key 8.
4. Before further work, remember the location of the lock. Replacing the ignition switch on a VAZ 2101-2107. Watch the video on how to replace the cylinder lock on a VAZ 2109! Replacing the door lock. Remove the pin from the side and remove the link.
5. Remove the spring and pull out the cylinder.
6. The grove where it was grub was lubricated with WD-40.
7. new grub
   Comes with a key. Do not remove it before installing the lock. Sometimes you need to carefully modify a new part using a file. This happens if it is made in China or is simply non-standard.
8. If you don't fit the pin into the hole freely, you'll need to give it some room.

replacing the lock cylinder VAZ 2108 2109 21099

In 2021, a new video hosting service appeared that pays everyone for views, likes and subscriptions. The channel is still wet.

replacing the lock cylinder on a VAZ-21099

Assembly occurs in reverse. Replacing the timing belt on a VAZ 2109. Carburetor YouTube. Be sure to connect the links and check the lock before working on the vehicle for the first time. This work will take you no more than an hour. The trim is always installed last after installing the locking mechanism.

Features of door adjustment

The adjustment work involves changing the height of the rods. The rod is fixed with plastic tips that have a spherical support inside. Correct installation of the door by pulling the groove. Next, you will need to turn it a little counterclockwise or clockwise. The lock is determined by choosing the ideal length. So be patient.

After the repair, you will have to adjust the bolt action mechanism. All materials in the section “VAZ 2109 silent blocks. replacement 2 replacement of crab silent blocks” k. By the time you move on to setting it up, you can already turn the panels towards the door, since the work will be done with the latch on the body. Move the lock up or down until you get the perfect result. Doors should be easy to close, without noise or effort. Replacing the timing belt of a VAZ 2109. Photo, video. This adjustment can be made without replacement. lock cylinders if you do not feel the need to use force when closing.

Features of door adjustment

Incorrect operation of the lock may be caused by problems with the door card. After long-term use, it sags, and sometimes it is simply installed incorrectly. Basic actions:

1. The lock latch, which is located on the stand, is adjustable. To do this you will need an impact screwdriver. The screws are first loosened, adjustments are made, then the fasteners are tightened.
2. Adjusting the response part if there is no softness when closing or a squeak is heard. The door moves outward using external adjustment bolts.
3. The bracket is dismantled using a hammer. After several blows the door moves. After this, the operation of the mechanism is checked. If the problem does not go away, the procedure is repeated.

How to replace the trunk lock on a VAZ 2113-VAZ 2115?

1) As for hatchbacks, the lock can be easily removed on them, but there will be no problems on sedans either, but the principle of replacement on two different bodies is different, first we’ll talk about hatchbacks, if you have a car with such a body, then remove them first the upholstery that is fastened inside the trunk lid with ten pistons, it can be removed very easily, all the pistons were pry off with a screwdriver and then the upholstery was put aside, for more details on how to do this, read the article: “Replacing a spoiler on cars”, point one in that Study the article in detail.

2) After the upholstery is removed, unscrew two bolts and thereby remove the lock from the car, but only when unscrewing the bolts, take into account the fact that under one of them there are several terminals, one of which goes to the tailgate wiper motor, and the other to brake light, well, that's it, the lock has been removed from the car.

Note! To adjust the lock on this type of car, take a spanner wrench (You can use a spanner if there is no spanner, there is simply a chance of breaking the bolts securing the lock) and use it to loosen the bolts securing the lock (Do not unscrew them completely, in this case, by the way, you are adjusting the position of the lock, because in a knocked down position, the trunk lid may be difficult to close, close with a blow, or it is very poorly fastened and opens at all on bumps), then move the latch in the desired direction, ensuring that the lock, when closing the trunk lid, enters the latch without strong force and that the trunk closes firmly (see photo 1), if you need to adjust the trunk lid in height (That is, the lid does not close well and there is play if you pull the lid), then in this case completely unscrew the bolts securing the latch, remove it and then the select the adjusting plates behind it (Always remember one thing, the more plates you put, the higher the trunk lid will stand and it will have a backlash, the fewer plates there are, the worse the trunk lid closes and the stronger it is pressed against the car body, and if there are no plates at all, then you simply won’t be able to close the lid, so look for a middle ground, see photo 2)!

3) As for sedans, they first remove the plastic clips using a screwdriver that secure the lock cover and then the cover is removed (see photo 1), and when it is removed, proceed to disconnect the rod, to do this, the tip of the rod (The rod is indicated in blue arrow in photo 2) remove it from the hole indicated by the green arrow, but keep in mind that the tip is bent and secured with a screw indicated by the yellow arrow, so first unscrew the screw, then straighten the bent end of the rod with pliers and only after that remove the rod from the hole in which it is is how this will all be done, remove the rod from the hole in the lock cylinder lever (see photo 3) and remove it, immediately after that unscrew the three nuts that secure the lock (see photo 4) to the trunk lid and remove it from studs and finally, unscrew the bolt that secures the lock cylinder (see photo 5) and remove it (see photo 6).

Replacing and adjusting the trunk lock

The luggage compartment is equipped with an identical lock as the driver's door. For dismantling you will need a standard set of equipment. Step-by-step instruction:

1. The handle unscrews. The trim, trim, and panel are removed.
2. The two dome lamp terminal connectors, the windshield wiper motor and the actuator are disconnected.
3. The lock is removed using pliers. The rods are turned off and the spring is removed.
4. A new mechanism is inserted. The spring returns to its place.
5. The rod is screwed on. Electronics are connected.

The price of a complete set of locks for the driver's door and trunk starts from 500 rubles.

Replacing the larva in Kalina

First of all, replacing the lock elements means that the door trim will be completely missing. Therefore, first we will figure out how to dismantle the trim on Lada Kalina cars. The second chapter is devoted to how to remove the larva and install a new one in its place. The last step will actually be the simplest.

Removing the door trim yourself

Numbers here indicate all fastening elements. But to get to them, you need to remove the screw cap “3”, as well as the inner door handle. The pawl handle also needs to be unscrewed.

If these actions are completed successfully, the casing begins to be dismantled, moving it away from the metal. Dismantling is carried out starting from any of the corners, but care must be taken: the pistons holding the plastic are fragile.

If the package includes power windows, you will need to disconnect the connector connected to the button block. Also, another similar connector is present in most trim levels - where there is a central lock. Both connectors must be disconnected.

All the steps described here involve electronics in any case.

Recommendations for changing the cylinder in a VAZ 2109 lock

If you disassemble the core, you can avoid replacing the cylinder or the entire mechanism. When the door opens with a creak, then most likely the internal pins are not deformed. Then lubrication work is carried out and the serviceability of the device is checked. Tips from the experts:

1. Partial repairs will bring life back to the castle for a short period of time. If serious problems arise, it is better to immediately replace the larva.
2. It is recommended to use silicone during lubrication.
3. When dismantling, you will need a set of screwdrivers: flat, Phillips, impact.

Experts advise purchasing clips in advance that hold the casing and spring, since during dismantling these parts most often become unusable.

Replacement of all door locks on VAZ 2108, VAZ 2109, VAZ 21099

Note! First, before starting work, from the car door on which you are going to replace any lock, first remove the trim; you will find information on how to remove the trim from a car door “in this article”!

Replacing the outside door handle:

1) First, disconnect both rods from the inner lock of the outer handle, to do this:

1. First, use a screwdriver to pry up the “door handle trigger rod” and then disconnect it.

2. Then, in the same way, disconnect the second rod “door lock switch rod” from the internal lock.

Note! For more details on where both rods of the internal lock are located, see the photo below!

2) Next, unscrew one inner retaining nut that secures the outer handle to the car door.

3) And after unscrewing the inner nut, completely unscrew the last nut, which is located on the edge of the door and also holds the outer handle.

4) And then remove the outer door opening handle, together with the rods, from the car door.

Replacing the lock cylinder:

1) First, remove the outside handle from the car door, if you still have it removed. (see "Removing the outer handle")

2) After removing the handle, using an awl or a thin screwdriver, push out the locking pin of the lock.

3) And then, on the back side of the handle, remove the lock leash.

4) Next, use a screwdriver to pry the spring of the outer handle cylinder.

5) And then remove it.

6) To complete the operation, insert the door opening key into the cylinder, and then remove the cylinder from the handle.

Replacement of external and internal door lock:

Replacing an external door lock: 1) In order to remove the external lock from a car door, read a separate article on this matter, published earlier on our website, the article is called: “Replacing an external lock”

Replacing the inner door lock: 1) First, use a screwdriver to remove both screws that secure the outer lock to the car door.

Note! It is best to unscrew these two screws with an impact screwdriver, but if you don’t have one, then use a regular screwdriver! (If you do not know about such a screwdriver or do not know how to use it, then look at the article entitled: “What is an impact screwdriver and how should it be used?”)

2) After unscrewing the screws, remove the outside lock from the car door.

3) And after that, remove the inner lock from the inside of the car door.

4) After removing the internal lock, remove from it using a screwdriver the lock washer that locks the “internal drive rod”.

5) And after disconnecting the lock washer, remove the “internal drive rod” from the lock.

6) Next, disconnect the plastic clamp that secures it from the “lock release button drive rod”, and then remove the rod from the lock.

Replacing the inner door handle:

1) First, use a screwdriver to unscrew both screws that secure the door handle to the car door itself.

General practical information about the design of the lock cylinder

Lock cylinder VAZ 2110

First, you need to imagine in general terms what the door lock cylinder of the VAZ 2110 means. From a practical point of view, the lock cylinder is the internal cylinder mechanism. Therefore, if the main cause of the malfunction lies in the cylinder, then simply replacing the internal cylinder is sufficient. What will happen when replacing a car lock cylinder:

• will allow you to return the lock to good condition, without changing it;
• will increase the current level of security of the castle itself;
• there will be a practical opportunity to replace the old key with a new one;
• By additionally equipping the lock with an armor plate, it will be possible to increase the degree of protection of the lock cylinder.

Lock cylinder for VAZ 2110

Note. When replacing the cylinder, the mechanical configuration of the lock changes, therefore, making a new key to replace the old one is a prerequisite for the operation.