How to connect PTF to a gazelle business with your own hands - diagram


Installing fog lights on a gazelle

Contact group: Write if you have any questions or ideas.

fog lamp diagram

When installing fog lights on a VAZ 2114 and modifications, on cars after 2005, in the cabin you will most likely find a connector for connecting the button connected to the mounting block. Therefore, you will only need to assemble the circuit in the engine compartment. The complete connection diagram is shown below. The disadvantage of this scheme is the same as that of the VAZ 2110 and I propose the same solution. diagram fog lights does not suffer from the disadvantages of circuits for VAZs, and almost all cars are equipped with these headlights. Unlike the Volga, its closest “relative”, the Gazelle , is practically not equipped with fog lights. Therefore, you have to make the connection yourself. When connecting, it should be taken into account that on new panels the central light switch used may have a position for turning on the fog lights and it can be used when connecting, so as not to install an additional button or key. The simplest connection diagram is shown below. The same scheme can be used for other cars.

The more broken down the car, the louder the radio screams from there.

Almost every car owner asks the question of improving roadway lighting. Drivers of Gazelle Business trucks, which are used exclusively for commercial transportation, will not be an exception. Considering weather conditions and cramped loading and unloading areas, equipping additional light sources will add convenience and safety.

The places under the PTF are closed with plastic plugs

About fog lights

Conventional headlights are of little use in fog, rain, or heavy snowfall: they make the space in front of the car not visible and are limited by a whitish veil, especially in long-distance mode. This happens due to the reflection of light from drops of fog, rain, and snowflakes.

In such a situation, an indispensable assistant is a fog lamp unit (FTL), the installation of which on any car will allow you to evenly illuminate the road and avoid dangerous situations.

But it is important not to forget that headlights are different, and knowing something about this will not hurt any driver. Russian fog lights produced at the Bosch-Ryazan and Avtosvet enterprises have good characteristics.

Quite a budget price – another advantage of such products

Russian fog lights produced at the Bosch-Ryazan and Avtosvet enterprises have good characteristics. Quite a budget price is another advantage of such products.

Headlights from Asian companies Al Khateeb and Saca are more attractive in appearance, but their cost is twice as high as Russian ones, and high power often leads to overheating and deformation of plastic parts.

The devices of the German company Hella are considered to be the highest quality fog optics, but this pleasure is not available to every driver due to the cost.

When purchasing, first of all, pay attention to the appearance of the headlight (set): “fog lights” have a marker in the shape of the letter “B”. Next, check the tightness between the diffuser and the reflector (housing)

Violation of the tightness of this connection will reduce the life of the headlight.

Where to post

We need to start by choosing the place where our new foglights will be located. Traditionally, either a car bumper or a cab roof is used for these purposes. However, with the second option there may be difficulties in coordinating with traffic rules.

Note! According to these standards, the use of the roof is permitted for vehicles with all-wheel drive or in difficult operating conditions - dirt roads, potholes, etc.

Additionally, you need to know other requirements of the traffic police rules.

So, the installation of Gazelle fog lights must meet the following standards:

Bumper mounting kit

Among other nuances that can be caused by installing fog lights on a Gazelle, you should pay attention to the shape of the products, as they can be rectangular, square, oval, etc. Place them in the places recommended by the manufacturer.

If this does not work, then you can cut holes in the existing bumper or buy a new one, specially prepared for this. The price of purchasing a new bumper may not be acceptable for every Gazelle owner, so we will further discuss how to do this without extra costs.

What to consider when connecting

When connecting, keep in mind that the new Gazelle instrument panels are equipped with a central switch, which has a separate position for the fog lights, so you don’t have to embed a separate button.

A number of points regulate where and how additional lighting fixtures should be installed:

In some cases, traffic regulations allow the installation of fog lights on the roof of a vehicle. For example, if we are talking about an all-wheel drive vehicle with high cross-country ability. Or its operating conditions are so harsh that even making stickers for the headlights is not able to protect them from stones.

PTF before installation

Install on the front bumper

At the same time, in the first photo you can see that the manufacturer has already designated places for future foglight mounts in the bumper. You can choose another place, not forgetting the recommendations of the traffic police officers stated above.

Again, there is quite a variety of headlights on the market, based on shape and size. Most often, headlights of rectangular, square or oval shape . But after the purchase you will have to decide where your lighting fixtures can be placed.

For example, a Gazelle Business fog light will require mounting holes, but the front bumper does not always provide this. Therefore, there are 3 main ways out of this situation:

Advice: purchasing an improved bumper design will allow you to avoid unnecessary movements and significantly simplify installation, although the price of such a product will require additional costs.

So, if we have established for ourselves the mounting location for the foglights, then it’s time to assemble the electrical circuit, and then introduce it into the standard one. Each kit, which is designed for additional lighting in bad weather conditions, includes not only headlights, but also electrical wiring to connect them, as well as an interrupt relay and a button to start the lighting.

The main stages of connection work

Here are sample connection instructions:

  1. First of all, in symmetrical places on the bumper we cut out two holes in which the light sources will be attached and thoroughly lubricate them with an anti-corrosion agent.
  2. We connect the purchased pair of foglights with wires. Check that the cross-section of the main wiring of the car is the same as that supplied with the headlights. It is generally accepted that the minimum cross-section diameter should be at least 0.75 mm.
  3. We de-energize the car battery.
  4. Wiring is carried out in accordance with the diagram that comes with the package.


Decoding connectors for connecting headlights to Gazelle

  • You need to open the housing of each headlight and pull out its optical element. This will be required so that you can carefully insert the halogen light bulb and not damage the housing with glass during the installation process.
  • After tightening the headlight housings, install the contact relay with the wiring facing down. This way we will protect it from moisture.
  • When you insert a halogen lamp into its optical element, do not allow your fingers to contact the surface of the bulb. Wear gloves or even wrap a rag around the flask. Grease on the surface of the bulb will significantly shorten the life of the light bulb.
  • We connect the wiring kit to the lamp and install the optical element.
  • Gazelle fog lights will be considered installed when you have completed all stages of work and provided power to the battery again. Now you can check the functionality of the device. Turn on the headlight only after complete assembly. The video in this article will give you the opportunity to visually see some of the work.

The role of relays and buttons

If the fog light kit you purchased does not have a relay, purchase one for the 3302. There it operates the rear fog lights. Normally, each kit should be equipped with electrical wiring with connectors, a relay breaker, a power button and a detailed instruction diagram for the assembly steps.


Pay close attention to the quality of wiring

Note! The wiring harness is not only possible, but also necessary to be routed into the space under the hood.

After this, decide on the place where the breaker relay will be attached:

  • The wiring from the relay will be led into the cabin through a specially designed technological hole.
  • You now need to find out where the button that turns on the fog light will be located in order to find out how to connect it to the standard electrical wiring of the Gazelle.
  • We need a relay for the reason that it saves the button - it may not withstand the current consumed by the fog lights. Some are used to connect a 3-position key: 1 wire is stretched to the dimensions circuit, the 2nd to the ignition, and the 3rd to the relay itself. This achieves 3 operating modes.


Light control unit for Gazelle

Installation location

Since the Traffic Rules must be strictly observed, the only correct place for installing fog lights can be the front bumper of the car.

In the photo - fog lights built into the bumper

Note! Traffic regulations prescribe restrictions on the location of additional lighting fixtures on the car. In particular, Gazelle fog lights should not be located above the low and high beam headlights. Also, they should not protrude more than 400 mm beyond the external dimensions, and the distance from the road surface to the headlights should be at least 25 cm.

The traffic rules and GOST 8769-75 allow the installation of fog lights and additional headlights on the roof, provided that the vehicle is operated in difficult road conditions:

On such routes, headlights with low mounting will not last long.

Advice: if you don’t want to explain yourself at every traffic police post about the “chandelier” on the cab, motivating your decision with concern for the safety of the headlights, then install fog lights only on the front bumper. And making headlight stickers from a special polymer film will protect the glass from gravel stones.

Where to install fog lights?

First of all, you need to decide where to install such headlights. This could be the front bumper or the roof of the car. The latter option is not excluded by traffic regulations, but only if we are talking about all-wheel drive models, or when installing headlights at the bottom can lead to their breakdown (for example, when traveling on dirt roads).

However, most experts, when advising on how to properly connect fog lights, agree that it is better to do this on the front bumper. But if you are looking for cheap truck rental, then among the vehicles offered there may be those with such headlights installed on the roof.

About fog lights

Conventional headlights are of little use in fog, rain, or heavy snowfall: they make the space in front of the car not visible and are limited by a whitish veil, especially in long-distance mode. This happens due to the reflection of light from drops of fog, rain, and snowflakes.

In such a situation, an indispensable assistant is a block whose installation on any car will allow you to evenly illuminate the road and avoid dangerous situations.

But it is important not to forget that there is discord, and knowing something about this will not hurt any driver. Russian fog lights produced at the Bosch-Ryazan and Avtosvet enterprises have good characteristics.

Quite a budget price - another advantage of such products

Russian fog lights produced at the Bosch-Ryazan and Avtosvet enterprises have good characteristics. Quite a budget price is another advantage of such products.

Headlights from Asian companies Al Khateeb and Saca are more attractive in appearance, but their cost is twice as high as Russian ones, and high power often leads to overheating and deformation of plastic parts.

The devices of the German company Hella are considered to be the highest quality fog optics, but this pleasure is not available to every driver due to the cost.

When purchasing, first of all, pay attention to the appearance of the headlight (set): “fog lights” have a marker in the shape of the letter “B”. Next, check the tightness between the diffuser and the reflector (housing)

Violation of the tightness of this connection will reduce the life of the headlight.

Installation and connection of PTF

To install, you first need to decide on the installation location. According to the rules, fog lights must be located below the head light, so they are installed on the front bumper. An important requirement when installing and operating a PTF is autonomous activation. This is due to the high power of the lamps required to diffuse light along the road surface. An intermediate relay is used for this purpose. In addition, fuses are used to provide additional safety.

It is better to purchase a bumper with an improved design. This will simplify installation and eliminate unnecessary steps.

Installation and connection of fog lights consists of a sequence of actions:

After installing the PTFs and connecting them to the on-board network, you need to check the system for functionality and correct connection.

Each car has its own use, largely depending on the owner. But if the conversation turns to Gazelle, then almost always we are talking about commercial transportation.

Moreover, the routes often end far from illuminated city streets.

Installing fog lights - Gazelle gets more luminous flux

Therefore, the issue of improving roadway lighting is more relevant than ever:

Note! Traffic regulations prescribe restrictions on the location of additional lighting fixtures on the car. In particular, Gazelle fog lights should not be located above the low and high beam headlights. Also, they should not protrude more than 400 mm beyond the external dimensions, and the distance from the road surface to the headlights should be at least 25 cm.

The traffic rules and GOST 8769-75 allow the installation of fog lights and additional headlights on the roof, provided that the vehicle is operated in difficult road conditions:

Advice: if you don’t want to explain yourself at every traffic police post about the “chandelier” on the cab, motivating your decision with concern for the safety of the headlights, then install fog lights only on the front bumper. And making headlight stickers from a special polymer film will protect the glass from gravel stones.

The main stages of connection work

Here are sample connection instructions:

  1. First of all, in symmetrical places on the bumper we cut out two holes in which the light sources will be attached and thoroughly lubricate them with an anti-corrosion agent.
  2. We connect the purchased pair of foglights with wires. Check that the cross-section of the main wiring of the car is the same as that supplied with the headlights. It is generally accepted that the minimum cross-section diameter should be at least 0.75 mm.
  3. We de-energize the car battery.
  4. Wiring is carried out in accordance with the diagram that comes with the package.

Decoding connectors for connecting headlights to Gazelle

  • You need to open the housing of each headlight and pull out its optical element. This will be required so that you can carefully insert the halogen light bulb and not damage the housing with glass during the installation process.
  • After tightening the headlight housings, install the contact relay with the wiring facing down. This way we will protect it from moisture.
  • When you insert a halogen lamp into its optical element, do not allow your fingers to contact the surface of the bulb. Wear gloves or even wrap a rag around the flask. Grease on the surface of the bulb will significantly shorten the life of the light bulb.
  • We connect the wiring kit to the lamp and install the optical element.
  • Gazelle fog lights will be considered installed when you have completed all stages of work and provided power to the battery again. Now you can check the functionality of the device. Turn on the headlight only after complete assembly. The video in this article will give you the opportunity to visually see some of the work.

The role of relays and buttons

If the fog light kit you purchased does not have a relay, purchase one for the 3302. There it operates the rear fog lights. Normally, each kit should be equipped with electrical wiring with connectors, a relay breaker, a power button and a detailed instruction diagram for the assembly steps. Pay close attention to the quality of wiring

Note! The wiring harness is not only possible, but also necessary to be routed into the space under the hood.

After this, decide on the place where the breaker relay will be attached:

  • The wiring from the relay will be led into the cabin through a specially designed technological hole.
  • You now need to find out where the button that turns on the fog light will be located in order to find out how to connect it to the standard electrical wiring of the Gazelle.
  • We need a relay for the reason that it saves the button - it may not withstand the current consumed by the fog lights. Some are used to connect a 3-position key: 1 wire is stretched to the dimensions circuit, the 2nd to the ignition, and the 3rd to the relay itself. This achieves 3 operating modes.

Replacement of rear light glass

The part is replaced in the second year. The rear light glass for the GAZelle is made of high-strength plastic, but it also fails: the surface cracks from vibrations due to leaky installation and damage during driving.

For replacement, an original part is selected that covers all rear light optics: dimensions, stops, turn signals. A total of 4 technical light lamps are installed on the block. During repairs, it is recommended to go through all the electrical wiring: the connectors on the rear lights in the GAZelle oxidize within 6 months, the electrical wiring often breaks due to incorrect connection and installation of the line.

Sequencing

When disassembling the element, the negative terminal from the battery is first removed. The glass is held on the block with 4 screws. The algorithm is as follows:

GAZelle drivers note frequent malfunctions of the signal lighting. During factory assembly, the left rear turn signal is powered directly from the front one and they forget to properly hide the wires in the engine compartment, as a result the elements quickly fail.

Source

Installing fog lights on a Gazelle

Each car has its own use, largely depending on the owner. But if the conversation turns to Gazelle, then almost always we are talking about commercial transportation.

Moreover, the routes often end far from illuminated city streets.

Therefore, the issue of improving roadway lighting is more relevant than ever:

In conclusion

We hope that the proposed material will be useful to you. Don’t forget to also protect the headlight glasses from foreign objects - headlight stickers are made for these purposes. Good luck on the road!

Did you like the article? Follow our channel for new ideas of useful car tips. Subscribe to us in Yandex.Zen. Subscribe.

Each car has its own use, largely depending on the owner. But if the conversation turns to Gazelle, then almost always we are talking about commercial transportation.

Moreover, the routes often end far from illuminated city streets.

Therefore, the issue of improving roadway lighting is more relevant than ever:

  • After all, standard headlights are not enough to maneuver in tight yards for loading and unloading operations;
  • And if we take into account weather conditions, then installing fog lights on a Gazelle is a conscious necessity, designed to protect the vehicle’s movement in poor visibility conditions.

Installation location

Note! Traffic regulations prescribe restrictions on the location of additional lighting fixtures on the car. In particular, Gazelle fog lights should not be located above the low and high beam headlights. Also, they should not protrude more than 400 mm beyond the external dimensions, and the distance from the road surface to the headlights should be at least 25 cm.

The traffic rules and GOST 8769-75 allow the installation of fog lights and additional headlights on the roof, provided that the vehicle is operated in difficult road conditions:

Advice: if you don’t want to explain yourself at every traffic police post about the “chandelier” on the cab, motivating your decision with concern for the safety of the headlights, then install fog lights only on the front bumper. And making headlight stickers from a special polymer film will protect the glass from gravel stones.

Choosing a location for installing headlights

An important point in the configuration of any car is the Gazelle; in this matter, it is no exception, taking into account the commercial all-weather nature of its operation. There are two options for installing headlights on the Gazelle: on the bumper and on the roof

Traditionally the first one is used

There are two options for installing headlights on the Gazelle: on the bumper and on the roof. Traditionally the first one is used.

The second option does not fit well with the traffic rules, since this document establishes restrictions on the placement on the vehicle of lighting equipment not provided by the factory. Installation of headlights on the roof is permitted only if the vehicle is operated in difficult conditions: gravel road surface, off-road.

The first option also has limitations: you can install fog lights on a Gazelle no higher than the level of conventional headlights, while the dimensions of the car are not violated by more than 400 mm, and the distance from the headlights to the road surface should not be less than 250 mm.

Installation process

To install the kit yourself, you can:

The fact is that the shape of the fog lights is different both in size and shape. Therefore, the connection of fog lights on the Gazelle will be carried out by you based on the dimensions of the selected lighting devices.

Today you can find the following products on sale:

And the question after purchasing the set you like is how to install lighting fixtures in places not intended for them. The thing is that companies strive to produce universal lighting devices, while there is no uniform standard among automotive manufacturers.

Bumper mounting methods

The difficulty is that the standard front bumper does not have slots for installing additional lighting fixtures.

Therefore, Gazelle owners have two options:

Advice! If the second option seems too expensive for you, since price is a decisive factor, then you still have the option of installing fog lights directly on the bumper using homemade fasteners.

Integration into the electrical circuit

Having figured out the mounting location, you have to connect the electrical components into a single circuit and integrate it into the standard one.

How to properly install fog lights on a Gazelle Business: connection diagram

The more broken down the car, the louder the radio screams from there.

Almost every car owner asks the question of improving roadway lighting. Drivers of Gazelle Business trucks, which are used exclusively for commercial transportation, will not be an exception. Considering weather conditions and cramped loading and unloading areas, equipping additional light sources will add convenience and safety.

The places under the PTF are closed with plastic plugs

Where to install fog lights

So, we install Gazelle Business fog lights ourselves. Let's start with the place where such an additional option can be mounted. However, if you pay attention to the traffic regulations , which say that fog lights should not be placed above the main beam headlights, it turns out that the only acceptable place should be considered the surface of the front bumper.

Color illustration of electrical components

One of the key requirements for the installation and operation of PTF is autonomous inclusion:

Note! One of the common mistakes is installing fog lights on a Gazelle Business and connecting them directly to the side lights of the main light. The current strength and the running light switch itself are not designed for the current that fog lights consume. This remark is also relevant for other models - see KIA fog lights.

How to connect PTF correctly

What to consider when connecting

When connecting, keep in mind that the new Gazelle instrument panels are equipped with a central switch, which has a separate position for the fog lights, so you don’t have to embed a separate button.

A number of points regulate where and how additional lighting fixtures should be installed:

In some cases, traffic regulations allow the installation of fog lights on the roof of a vehicle. For example, if we are talking about an all-wheel drive vehicle with high cross-country ability. Or its operating conditions are so harsh that even making stickers for the headlights is not able to protect them from stones.

PTF before installation

Install on the front bumper

At the same time, in the first photo you can see that the manufacturer has already designated places for future foglight mounts in the bumper. You can choose another place, not forgetting the recommendations of the traffic police officers stated above.

Again, there is quite a variety of headlights on the market, based on shape and size. Most often, headlights of rectangular, square or oval shape . But after the purchase you will have to decide where your lighting fixtures can be placed.

For example, a Gazelle Business fog light will require mounting holes, but the front bumper does not always provide this. Therefore, there are 3 main ways out of this situation:

Option with seats

Advice: purchasing an improved bumper design will allow you to avoid unnecessary movements and significantly simplify installation, although the price of such a product will require additional costs.

So, if we have established for ourselves the mounting location for the foglights, then it’s time to assemble the electrical circuit, and then introduce it into the standard one. Each kit, which is designed for additional lighting in bad weather conditions, includes not only headlights, but also electrical wiring to connect them, as well as an interrupt relay and a button to start the lighting.

The kit usually also contains instructions that help you correctly connect and route the wiring to the Gazelle - this will also be useful.

We fix the relay in the engine compartment

Basic sequence of actions

The work itself on connecting the fog lights to the Business Gazelle will be carried out as follows:

Connecting the PTF to the control unit in the cabin

Once we have the entire circuit assembled, we need to check its operation and the correct connection of the wiring to the relay.

Note! Failure to follow safety guidelines can cause an unprotected circuit to short out, resulting in the failure of incandescent lamps and wiring.

Assembly order

  1. The first step is to make and connect the connectors to the fog lights, screw the ground wire (brown in the diagram) through the terminal to the body. Lead the positive one (blue in the diagram) to the battery area (it will be connected to the relay, terminal 30).
  2. We fix the relay in a suitable place and connect the wires. Red (87) to the battery via a fuse (you can use a relay with a built-in fuse). with a nominal value of 30 A. Black (86) to the body through the terminal (possibly to the battery negative). We run the control wire (green) from terminal 85 into the passenger compartment (drilling the engine shield is allowed). Pairs of terminals 85-86 and 87-30 are interchangeable.
  3. We install the button in any convenient place and follow some rules when connecting.

We choose the option of turning on the foglights with our own hands:

  • autonomous (it turns on regardless of anything, but there is a chance to completely discharge the battery by accidentally forgetting to turn off the fogs) we connect to the dimensions or constant +ACC.
  • use only when the ignition is on (it is not possible to use the backlight, for example from an alarm), take the plus from the ignition switch or look for IGN1, or better yet, IGN2 according to the circuit, device or control light. That's it, let's check the functionality.
  • The power button can be used from the rear fog lights.
  • In connections it is better to use connection terminals with protective heat shrink rather than twisting and soldering.
  • It is advisable to pack all non-standard wiring in corrugated material, which is both more aesthetically pleasing and safer.
Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]